SBDE520NW (P1181201W W) Amana Refrigerator - Instructions

Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge.
Probably took about fifteen minutes total.

Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.

Called Parts Select on Wednesday. Spoke to tech who found the exact part I needed at less than the price on the site. Said it would be 3-5 days, no problem. When I got home Thursday afternoon, part was already there ready to be installed. Very pleased.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

Removed the old one put in a new one, fairly simple. Would have been much easier if I had called the manufacturer first then ordered the part. The first part I ordered was the ice bucket, I thought I was getting the crusher mechanism, but it turned out to be the bucket only. When I finally got the right part it was really easy. I went ahead and kept the new bucket anyway.

I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.

After an hour of searching the wire schematic diagram on the rear of the box , i looked for an obvious problem. Once I learned that this unit has a defrost switch built in in the control panel under the kick plate on the front of the unit, I pulled the large box out to reveal the small control panel with diods and computer chips mounted on the board with 8 wires running to that board, I learned that a mouse had somehow gotten into the box and crawled across the chip board, there he was fried and apparently the current continued to flow through his body and when the deterioration process reach acertain point my Amana decided it would not work. It was a very expensive unit and was told it would last 30 to 40 years with maint. So far it has lasted 17 years. Anyway replaced switch and the front handle of the unit while I had it apart for a good cleaning. The handle was a cinch.
Thanks
Jeff

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Took a toital of 15 minutes to exchange the bucket. A total of 4 screws to remove the auger and front of the bucket. Anyone can do this repair!!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

I've been messing around with the old part for literally years. Every now and then the metal agitator rod would spin out of the plastic cup that joins it to the freezer. I'd have to disassemble it and try to get it back into alignment. This time nothing worked, so I ordered a new assembly. It arrived even more promptly than PartSelect predicted and it installed in five minutes. I couldn't be happier!

Called amana repair to install new part , but worker called in sick. did it myself, was easy, only one phillips head screw and part slid out. looks like a florescent light starter with a wire attached with a loop on the end.very easy and thanks to the super fast delivery..next day, i could hardly believe it...

The DIY video was very handy and precise to every visual detail needed for anyone to do their very own repair. It doesn't get any better than that.