S160 - Instructions

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done

Now if you just sold faucet parts I'd be all set.

Replace filter

Unplugged and removed the old grill element by hand and installed the replacement element by plugging it into the socket. Tools were not required for this and it took less than five minutes. The new element is great and heats much better than the original did before it broke.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

Simple plug in.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

needed hammer to help loose screws .pulled out and replaced leement

Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.

First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.

First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.

Just replaced old with new, it plugs in same as old.

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.