RUD3000DB3 Roper Dishwasher - Instructions

Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.

Trial and error. The spring was difficult to install, the pin and door were easy.

Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Replaced front cover. result, bright, clean dished.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

Removed dispenser cover by using flat screwdriver, then slid the lid hinge pin and lid spring by pushing the lid hinge pin out on the silverware trade side. Then I put the lid hinge pin back into its place, once started I put the lid hinge spring on the lid hinge pin and pushed the pin into place, used flat screwdriver to put the lid spring in place, then I snapped the soap dispenser cover on the lid hinge pin. It took me about 5 minutes to remove and replace these parts, a very easy repair.

Replaced the lower rack. The replacement part had the wheels attached. No assembly required.

removed the 2 water deflector and slipped the new ones in , in place.. very easy to do but it didn't seem to stop the leak so ordered the door gasket

Received new rack in record time(very impressed with the delivery time)installed one part for the removable rack in the rear and simply replaced the old with the new.

I followed the video's from Parts Select and it took me less than 3 minutes to replace these parts. I did find it easier to use a screwdriver to lift the u shape of the spring over the detergent cup as the pliers tended to pull on the spring too much. Couldn't have been easier or faster, awesome!

After emptying the dishwasher the bottom had no water in it. A few hours later there was water in bottom. This told me the inlet valve was leaking. I took the bottom kick plate panels off. Directly in front on left side was the water inlet valve. Remove mounting screw, disconnect electrical connection, the water feed and discharge hose and remove valve. Install new valve. 100% DONE! Reinstall front panels after checking for leaks. At 71 years of age my typical 20 minute job actually took less time.

Took out old dishwasher rack and replaced with new.

This was stupidly easy! I found Parts Select from a Google search on making the repair. That took me to a YouTube video that Parts Select had posted on how to repair. I followed the instructions and it was fixed in 10 minutes and that was only because I took my time. I ordered the part online from a link on YouTube and I had it in two days............. Unbelievable!!!!

I paid a repairman over $100 to tell me he could find nothing wrong with my leaking dishwasher (it didn't leak when he ran it). I narrowed down the problem to a missing water deflector, but decided to replace the door gasket as well. It took less than 5 minutes to do the job. The only tool I used was a pair of needle-nose pliers to grasp the old door gasket and get it coming out of the groove. Thanks PARTSELECT for super-fast shipping and a website that is easy to navigate. I'll be coming back, 'cause all of my appliances are getting some age on them!

I used a screwdriver as a wedge to remove the existing panel and inserted the new black panel into the groves located on the front of the dishwasher. Installation was easy because I followed the instructions from the website. Piece of cake. Less than 2 mins.