RM973PXLT0 Whirlpool Microwave Oven Combo - Instructions

Replaced with the new burner works like new. Thanks a bunch!

grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

Before ordering any parts I remembered seeing a fan above the nylon roof of the microwave. I had seen a belt that drove it on a prior repair 3 years ago.

I then removed 1 screw holding the electrical panel so I could tilt it open. Since power was still plugged in I didn't put my hand in. I used a flashlight and the broken belt.

I could also see the moter that turned the belt and tested it by starting and stopping the microwave and could see the motor pulley spin when it slowed to a stop. I then closed the control panel and screwed it in place.

That confirmed I proceded to go to the internet with the model # for the rane/microwave and looked for parts.

I had an easy job looking the part and saw that the fan as I had called it was named Stirrer because it kept stirring the microwaves over the food.

Overall I looked at 2 venders and chose Part Select because they showed the same catalog page and part numbers, and they had a better price.

I had my part/ belt in 4 working days and installed the new belt in about 15 minutes. This time unplugging the range so there was no power to be concerned with. It was a matter of picking out the old belt and putting the new belt on the motor then walking the belt over the large pulley at the Stirrer since the belt will stretch a bit.

Buttoned it up and later tested with popcorn and it left only a small amount of old maids.

Thanks, Walt

Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

The repair was a trivial effort as all parts simply lift off the range top by hand. The impetus for replacement was pretty much looks driven.

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.