RJS369 Caloric - Instructions

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Daughter and family came to visit Gramps for the weekend; Saturday morning, arose and opened a couple of cans of grand buscuits. Set aside to let rise then turned oven on to preheat. Came back later and oven did not work. Stove top worked, broiler worked, but no oven. What to do, didn't want to waste dough; perhaps salvage for dumplings, no; make poorboy doughnuts, no; Aha, lets use the outside gas grill, never done it, worth the try, remember old camping days except using gas. Worked like a charm, crisis over. Now back to oven. Since everything worked except the oven burner problem could be in the igniter, or oven control. Removed covers to burner assembly, pulled igniter, checked for continuity across the two leads. No go. Wait, need to check oven control, placed voltmeter across incomming leads, turned oven controls on and had voltage. Conclusion, igniter bad. Also noticed a small rust hole in the burner tube next to igniter, not good. Went on-line to PartsSelect, entered make and model number. No model but gave choice close to model. Viewed pictures, found one that came close. Placed order. Parts came in a very short time. Matched new parts to old. perfect. Removed burner tube and installed new one, one screw, simple. Wire nut the incomming leads to igniter and install, three screws, simple. Turned oven on, igniter glows bright, gas comes on, good blue flame, no need to adjust air inlet vents on burner tube. Turned off oven, replaced covers, then turned on oven, baked cornbread and enjoyed. Thanks, back in business. Dave

Removed old ignightor and installed new one

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carried back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

Bought a new one. . Three years later =)

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

ordered new broiler pan