Models > RF268ABPNXAA > Instructions

RF268ABPNXAA Samsung Refrigerator - Instructions

All Instructions for the RF268ABPNXAA
31 - 41 of 41
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator was too cold - down to 18 degrees Fahrenheit.
Removed shelves. Removed back cover. Removed old sensor. Installed new sensor. Replaced back cover. Replaced shelves. Works fine.
Parts Used:
Temperature Sensor
  • Bill from RALEIGH, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring replacement on Mullion Door
had to replace the spring on the Mullion door . the how to video helped however the demonstration shows putting the spring on in the opposite way that my door calls for, so just I turned the spring around and done, other than that easy as pie.
thanks
Chris F.
Parts Used:
Spring PIN - French
  • Chris from YORK, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
icemaker would not stop making ice
removed the front food tray
removed the broken ice maker shut off arm from the left side of the ice maker using a short Phillips screw driver, very little room between the
ice maker and the side of the fridge.
secured the new ice maker shut off arm with the same Phillips head
screw, the arm self positions via a locating notch
Parts Used:
Refrigerator Ice Maker Shut-Off Arm
  • John from HILLIARD, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door
Replaced the spring on my French door refrigerator
Was super easy
Parts Used:
Door Mullion Spring
  • Kathy from BUTTE, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer handle had broken free from the left side of the door.
On both sides of the door there is a pop off cover that houses the broken mechanism. I popped off the cover and exposed the screws the attached the handle to the opening mechanism. removing those screws I removed the handle from the freezer door. I replaced the broken plastic piece on the handle . Reattached the repaired handle assembly to the door with the 4 screws. Reinstalled the cover.
Parts Used:
Handle End Cap - Gray - Left Side
  • Kathleen from FLORISSANT, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Brokjen spring
Lifted out the broken part and replaced with new spring.
Parts Used:
Door Mullion Spring
  • Sharol from Culdesac, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
brackets broke that hold the tiltable tray for the freezer
Extremely simple, remove the old tray brackets and snap the news one in place. Put just enough pressure till you here them click in place.
Parts Used:
Support - Guard Freezer Support - Guard Freezer
  • Jerry from Manvel, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
french spring broke
after receiving spring installed spring in seconds. Thanks partselect.com Ryan Cappell
Parts Used:
Door Mullion Spring
  • RYAN from RIVERBANK, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We misplaced the mounting screws for our handles while moving.
It was easy! I just used an alan wrench to losen the side bolt, then slid the handle into the new mounting screws that I had hand-screwed and then tightened it all up.
Parts Used:
Handle Mounting Screw
  • Sara from BAKERS MILLS, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
French spring broke.
pushed new spring in.
Parts Used:
Door Mullion Spring
  • Andrew from Bensalem, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice tray had cracked and broken. The water is still not filling up my ice tray.
The replacement was fairly simple. I removed the existing tray and detached the water line. Once the water line water reattached to the new tray I inserted into the ice maker.

*** The problem I'm having now is the water is not filling up the tray***
Not sure what I did wrong? Any help would be greatly appreciated!!!
Parts Used:
Ice Cube Tray
  • Timothy from SALISBURY, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
5 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RF268ABPNXAA
31 - 41 of 41