All Installation Instructions for Samsung Refrigerator RF267AEPN/XAA

Broken spring on french door

Placed lower spring leg in hole first. Manipulated upper spring leg into upper hole with needle nose pliers.

Parts Used:

Door Mullion Spring

John from CADILLAC, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker leaking water into ice bin.

Took out Philip’s screw. Applied heat from hand hair dryer for one minute. Unplugged wire plug. Pushed ice maker lever to release and gently pulled forward.Removed old ice maker and replaced with a new maker.
Plugged in wire harness and replaced wire cover.

Parts Used:

Icemaker Assembly - 9 Cube

David from WEST JORDAN, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

door spring

replacing broken french door spring.

Parts Used:

Door Mullion Spring

Libor from Danbury, CT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Just follow instructions. Easy

Held spring with needle nose pliers and slipped into place

Parts Used:

Door Mullion Spring

David from NORTHWOOD, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Ice maker no longer made ice.

Prepare the area
Open the refrigerator door(s). Remove the ice bucket/bin by lifting it up and pulling it out (it usually slides forward after a slight lift). Set it aside. Empty any loose ice.
Remove the ice maker cover / upper panel (if present)
There is often a plastic cover or shroud over or in front of the ice maker. Gently pull or pry it off using a flathead screwdriver on the release tabs. Some models have screws holding this cover. Note the orientation for reassembly.
Disconnect the wiring harness
Locate the electrical connector (usually a 12-pin plug) on the side or back of the ice maker.
Press the release tab on the connector and gently pull it apart. Do not yank the wires. Tuck the harness aside safely.
Remove the mounting screws
There are typically 2 screws (Phillips) securing the ice maker to the refrigerator wall or bracket — one on the side/top and possibly another. Support the ice maker with one hand while removing the screws so it doesn’t drop.

Remove the old ice maker
Carefully tilt and pull the unit forward/out. It may have tabs or hooks that need to be released. Wiggle gently if stuck. Avoid forcing it to prevent breaking plastic parts or damaging the fill tube.

Install the new ice maker (DA97-07365G)
Position the new assembly in the same orientation. Align any tabs, hooks, or slots with the mounting bracket.
Reinstall the 2 mounting screws snugly (do not overtighten).
Reconnect the wiring harness firmly until it clicks.
Reassemble the cover/panel
Snap or screw the cover back into place.

Reinstall the ice bucket
Slide the ice bin back in until it seats properly.

Power on and test
Plug the refrigerator back in.
The ice maker may take time to cool down and begin a cycle (several hours).
Press the Test/Reset button on the ice maker (small button on the side or front of the unit) to run a test cycle if available. You should hear the motor and eventually a fill.
Check the control panel on the door — ensure Ice Maker is turned On (not Ice Off).
Monitor for the first batch of ice (can take 6–24 hours depending on temperature and usage).

Parts Used:

Icemaker Assembly - 9 Cube

Johnathan from Nashville, TN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Refrigerator was too cold - down to 18 degrees Fahrenheit.

Removed shelves. Removed back cover. Removed old sensor. Installed new sensor. Replaced back cover. Replaced shelves. Works fine.

Parts Used:

Temperature Sensor

Bill from RALEIGH, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

5 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Door

Replaced the spring on my French door refrigerator
Was super easy

Parts Used:

Door Mullion Spring

Kathy from BUTTE, MT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

french door mullion busted

Piece of pie! Took of the screw caps, the screws, disconnected the wire switch and reversed direction with the new one. 10 minutes tops.

Parts Used:

French Assembly

JOHN from ARLINGTON, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Brokjen spring

Lifted out the broken part and replaced with new spring.

Parts Used:

Door Mullion Spring

Sharol from Culdesac, ID
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

french spring broke

after receiving spring installed spring in seconds. Thanks partselect.com Ryan Cappell

Parts Used:

Door Mullion Spring

RYAN from RIVERBANK, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

We misplaced the mounting screws for our handles while moving.

It was easy! I just used an alan wrench to losen the side bolt, then slid the handle into the new mounting screws that I had hand-screwed and then tightened it all up.

Parts Used: