RB787WB1WW Hotpoint Range - Instructions

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

This was extremely easy! I unscrewed two screws, pulled out the old element, inserted the new element and screwed the screws back in. Also, this part came very quickly through the mail. If needed, I will definitely use this site for repairs again.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Remove two screws to loosen the ceramic top....prop top open and change part...the part was exactly the same...change wires from one to the other and transfer clamps.....1st grade craft class would have done it in half the time I did......you folks have your parts inventory and description application to a science.....God Bless

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.

First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.

First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.

I unpluged stove then opened slightly oven door and lifted it off to get closer. Then with a light to help I took out two screws and pulled the element out. I didn't need pliers to get the wires that are put on with slide on clips. you may need a pair. put wires on slide in place put screws back ,replace door, plug it in and test. Very easy.

Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into place replaced two screws that hold cook top down, pluged back into outlet. DONE!

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!