RB757BC1WH Hotpoint Range - Instructions

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue

Did the repair just like the video shows.

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

took out a couple of screws and replaced with new switch, plugged in switch wires. very easy

Followed directions given by previous customers problems which we found on the internet.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

unplug it and plug the new one in

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

All I had to do was to plug the burner in and it worked.

I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired