All Installation Instructions for Whirlpool Wall Oven RB260PXK0

unit burned out

grandson removed the two screws holding in the burned out unit and removed the two wires, installed them into the new unit and put the prongs into place. very easy and certainly very economic. delivery was quick and postage was reasonable. Thank you.

Parts Used:

Oven Bake Element 2600w 240v

Mildred from VALE, SD
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

broken oven temp control knob

With the Perfect Replacement Part, the 'installation' was simply putting the new knob on!..:-)

Parts Used:

Range Control Knob

Eric from WEEKI WACHEE, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven didn't get over 300 deg. F.

Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!

Parts Used:

Oven Bake Element 2600w 240v

Barry from WOODSTOCK, GA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Lower oven element not working.

1. Turn off oven.
2. Switch off circuit braker to oven.
3. Remove two screws holding element.
4. Pull element out to expose connectors.
5. Disconnect connectors and remove element.
6. Reverse procedure for installation.

Parts Used:

Oven Bake Element 2600w 240v

Doug from Puyallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bake Element Failed

I had previously partially removed the element and tested with multi-meter to determine that it was not working (open circuit). Repair procedure follows:

Turned off Power
Removed 2 retaining screws
Pulled element out part way
Removed 2 spade connectors supplying power
Replaced element w/new element
Reversed procedure
Tested Oven; worked fine.

Parts Used:

Oven Bake Element 2600w 240v

Johnson from Norwood, CO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Bake Element went bad, will not work.

As soon the Bake Element has arive, I install it no more than 5 min... All I nedd was a Screw driver. It was so easy, Thank You PartSelet!

Parts Used:

Oven Bake Element 2600w 240v

Kent from Spooner, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

bake element was broken

was very easy to install I only needed a phillips screwdriver to remove old part and install new one.

Parts Used:

Oven Bake Element 2600w 240v

carolyn from ROGERSVILLE, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

light wont come on

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

Parts Used:

SWTCH-LITE

James from Fort Collins, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Broken knob

Only replaced a knob. Pulled the old one off and put the knew one on.

Parts Used:

Timer Knob

John from GERMANTOWN, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Replacing the cracked oven knob.

Was waiting on my friend's boyfriend who is a contractor to switch this knob out but figured it out myself. It just slides on and off with no tools. I am so proud of myself for completing the repair all by myself on my 37 year old oven. My other knob just cracked and I was afraid the inside of the knob was damaged but it is not. Working like a charm now.

Parts Used:

Range Control Knob

Bonnie from Monroe, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The two oven control knobs were broken.

The new knobs slide on and fit perfectly. No tools or labor required.

Parts Used:

Range Control Knob

Doris from ROBBINS, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Bake Element burned out

Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.

Parts Used:

Oven Bake Element 2600w 240v

Joseph from MIDDLE RIVER, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven Heating element had a melt down and small explosion

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

Parts Used:

Oven Bake Element 2600w 240v