RB100PXK0 Whirlpool Wall Oven - Instructions

My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

The element comes with the element attached to the bracket that holds it in place in the top of the oven. I had removed the 2 screws-one on each side--on the old element and disconnected the spade connections on the wiring after I pulled the element out far enough to expose them. I then reconnected the new element, pushed it back into place and re-installed the screws that hold it in place. A pretty simple job but I got a tremendous feeling of accomplishment after it was done. Saved a bunch of $$$ also!!

remove two screws at rear of heat element unit. gently pull element to expose wires connected to heat unit. pull connectors apart on each end (don't let wire slip back into wall hole). connect new unit to wires, insert back into holes and replace screws into back wall of oven. Done... Now that I have done it once, it would now take less than 15 minutes.

The only problem we had was hanging on to the small screws that held the element up. No power screw drivers, so it took a little while to keep a hold of those screws. Considering we are 87 and 84 we feel great that we were able to replace both the bottom element and the broiler. I like the stove, and preferred not to shop for a new one. "Thanks for prompt great service and the video helped. Patty Montag

Fast shipping and the part was very easily installed.

I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

First, turn off the breaker to the oven, then turn off the service disconnect to the whoe house. I play safe.) Open the door, pull out the oven racks to allow space. Using a Phillips screw driver, unscrew the screws near the front of the oven to loosen the element. Using both hands, pull the element straight out of the holes in the back of the oven, where you will find electric wires attached to them. Pull the ends of the element off the wire connectors. Throw it away. Get you new element, attach the element ends to the connectors. Raise it up to the top of the oven and screw the screws back in to the holes in the top of the oven. You are finished. (The only reason this took me 30 minutes is because I am an old 79 year old granny and can't bend so well, or see so well. I had to use a little acrylic paint on my finger tips to mark the screw holes, it was taking too long to find them the old way, by feel.) GG

Four screws hold the broiler element. I removed the two at the top, then removed the two screwed to the back keeping the element in place. I slowly pulled the element forward and used alligator clips to keep the wire connectors from falling back behind the oven. I disconnected the wires from the broken element and replaced it with the new element. I removed the alligator clips. I screwed the two screws on the back and the two on top and I was finished. Problem solved.

I was able to locate the exact part needed to make my older oven work like new again. Thanks for the great online source for hard to find parts. All I had to do was remove the old one and replace it with th new one. It fit perfectly.

I observed that the lower heating element was attached to the lower rear of the oven by two stainless phillips screws. I removed the screws and gently pulled the element outward. The element came out easily with two large red wires attached (one on each side). I unplugged the wires and extracted the old element. I used this as an opportunity to clean the floor of the oven that was hard to get at with the element in place. I installed the new element by plugging in the two red wires and used the same two stainless screws to reattach.

turn off the oven breaker - unscrew both sides of element, pull through holes & remove wire ends. Replace with new element, reversing procedure - turn on breaker & you're good to go.

Simple to unscrew the 2 screws holding the element to the back of the oven. Unclip the wires.

Unscrewed the two screws holding the rear plate of the element. Pulled the element out far emough to reach the plugs on each side. Disconnected the plugs and plugged in the new element. Put the screws back in and it was ready to go. This was the second replacement in the last five years.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.