PTI22MFMALWW General Electric Refrigerator - Instructions

-unplugged the refrigerator
-replaced water filter inside refrigerator
-turned off water suppy at valve
-unscrewed tin cover on lower part of refrig
-took brace off that holds the double water valve
-disconnected water lines and caught excess water in a bucket
-pulled out both electrical plugs out of old dual pump
-blew out with air the black water line that runs diagonally from the part to the top of refrig going into ice make(to make sure not clogged)
- Installed the new part and reconnected all of the above.
plugged in the refrigerator
opened the valve to let water flow inot refrigerator.
done--but still no ice cubes? HELP!

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

Rolled the fridge away from the wall, unplugged the unit from the wall outlet, and removed the back panel by taking out the 6 1/4" nuts that held it in place. Vacuumed the dirt and dust out, and sneezed viscously for 2 minutes. Removed the 3/16th nut holding the water relay. removed the inlet water line, and quickly replaced it. dried off, then went down stairs and turned off the saddle valve. mopped up the water, then removed the water inlet valve. Removed the 2 water lines to the unit (Ice and water feeds) and removed the 2 wire connectors. reversed the process in installation, except the drying myself off part, and sneezing from the dust and dirt.

Just turn the cartilage out and put the new one. Very simple

Replacing the water valve was easy - the video was excellent. However, the problem was not solved - no water even after replacing the water valve. Anyone have any other thoughts?

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

Removed back panel. Cut the water lines and replaced the double outlet water valve. The only issue was the long period of time until the water flowed from the outlet. Be prepared to wait, it will take some time for the water to flow.

Replaced Water Filter (twist off old filter; twist on new.)

with my hands

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!

Followed the instructions and replaced the door recess.

I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks

simply read the instructions

Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.