All Installation Instructions for General Electric Wall Oven PSB9240SV1SS

no power in microwave in turn table wouldn't turn light would work act like door was open

remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now

Parts Used:

Primary Door Interlock Switch

johnny from port orange, FL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

5 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Try to heat food and fuse would blow.

Went on Youtube and pulled up how to fix a microwave.

Parts Used:

Capacitor

bart from new sarpy, LA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

8 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Timer, light and control pad worked. Turn table and heat did not work. Oven would not start up.

I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followed them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.

Parts Used:

Microwave Fuse

Pearlie from Beulaville, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The unit would run when the door was open!

First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.

Parts Used:

Primary Door Interlock Switch

Mike from BLUFFTON, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace bulb under microwave

Part Select sent the wrong part I did not realize it until prong broke off one of the bulbs. They sent 130v instead of 120v. Return bulbs awaiting resolution.

Parts Used:

HALOGEN LAMP

Andrew from COLUMBIA, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thermostat quit.

Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.

Parts Used:

THERMOSTAT

Tony from ITHACA, MI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

No problem. Rollers on guide had worn out.

Just put it in place in you Advantium and place your glass tray on it and you’re ready to roll

Parts Used:

Roller Guide

Maeta from CLOVERDALE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Microwave’s Halogen Light Bulb burned out.

Our Microwave’s Halogen Light Bulb burned out.

We looked in our manual and were able to take the cover off to get to the bulb, but we were unable to unscrew the builb and the bulb in the manual did not match the size of the one you offer (size and part number were different)

We called 1-888-738-4871.

Gentleman who answered was very knowledgeable: answered all of our questions (PULL THE OLD BULB OUT) and assisted us by ordering replacement bulbs.

We (more importantly my wife) were very pleased with the result.

Parts Used:

HALOGEN LAMP

PETER from NEW YORK, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Bulb burned out

change bulb

Parts Used:

HALOGEN LAMP

Richard from SPRINGFIELD, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

No heat

Replace the fuses

Parts Used:

Microwave Fuse

Edwin from New York, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

No heat.

Replaced the fuse. Result; did not fix the problem.

Parts Used:

Microwave Fuse

Mack from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

no night light

took out cover by removing cover. pulled out light bulbs replaced with new bulbs. replaced cover and tighten screw. very easy

Parts Used:

HALOGEN LAMP

CURTIS from WINDSOR, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 14 people found this instruction helpful.

Was this instruction helpful to you?

microwave won't heat

bought a fuse but that didn't solve the problem. Guess I need a new microwave

Parts Used:

Microwave Fuse

Stephanie from Kernersville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Microwave would not heat

I went on line, put in microwave repair and watched a video on repair. I then took the oven down from over the range and took it apart. I could see were the magnetron had burned out. There was a hole with obvious burn marks. I went on line looking for the needed part. I clicked on PartSelect and order the magnetron. I received the part within three days, regular shipping. As I had not put the oven back together it took only a few moments to save 150 to 200+ dollars. I put it back together and happy, happy me, it worked.

Parts Used: