Models > PDWF600R10BB > Instructions

PDWF600R10BB General Electric Dishwasher - Instructions

All Instructions for the PDWF600R10BB
46 - 60 of 189
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Would NOT drain
Flipped washer on side
Did repair from bottom
Really easy repair
Parts Used:
Motor and Drain Pump
  • Nathaniel from HAWKINSVILLE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost Rinse Aid cap
Inserted new cap purchased from PartSelect.
Parts Used:
Rinse Aid Cap
  • Jerome from Arlington, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced dishwasher but had the wrong drain hose.
Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.
Parts Used:
Drain Tube Kit CLAMP
  • Victor from Phoenix, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher door would not latch
opened door removed screws holding back side of door took out front panel with latch assembley found broken part and replaced it
Parts Used:
Door Handle Actuator Silverware Basket Retainer Handle - Black Recess Door Spring Latch Handle
  • CHRISTOPHER from CEDAR KNOLLS, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
12 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dishwasher detergent dispenser was broken.
The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!
Parts Used:
Detergent Dispenser with Rinse Cap
  • Richard from BATESVILLE, IN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not fill with water
Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.
Parts Used:
Water Inlet Valve
  • James from JONESBOROUGH, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse cap was broken
Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions
Parts Used:
Detergent Dispenser with Rinse Cap
  • DENNIS from MAUMEE, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leakage at valve
I watched the video that came with email on part. Gave instructions on how to. Thank you !
Parts Used:
Water Inlet Valve
  • Jimmy G from SPRING, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser Cap Missing
Ordered new cap and put it on when it arrived.
Simple
Parts Used:
Rinse Aid Cap
  • Larry from Denvr, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wire basket rusting.
The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.
Parts Used:
Upper Dishrack Kit Complete Lower Service Rack Assembly
  • Scott from pleasanton, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing cap
I placed the missing cap into the dispenser.
Parts Used:
Rinse Aid Cap
  • Jean from White Plains, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The soap dispenser would not close.
This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.
Parts Used:
Detergent Dispenser with Rinse Cap
  • tim from prior lake, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rack was rusted and broken.
It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!
Parts Used:
Complete Lower Service Rack Assembly
  • Amelia from PEORIA, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishes were not drying inside the dishwasher after the dishwasher cycle completed
The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.
Parts Used:
Heating Element
  • Christopher from GLEN ALLEN, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
Parts Used:
Hinge Arm Link
  • Ron from SOUTHPORT, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDWF600R10BB
46 - 60 of 189