PDW9700J00II General Electric Dishwasher - Instructions

Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.

We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!

Followed instructions on how-to video on website on how to remove and replace lower spray arm.

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

The noise came from the dishwasher door. Removed the Phillips screws from the door edge to gain access by separating the front of the door. Had to disconnect some of the electrical connectors to allow more access. Disconnected the blower motor connector. Removed the screws holding the motor assembly and removed the blower motor. Installed the new blower motor and reconnected the electrical connectors. Reassembled the door and cycled the dishwasher. Very quiet now!

Removed dishwasher from under counter. Removed both cable pulleys and bushings. Threaded new cables and remounted pulleys and bushings. Finally stretched springs onto cables. Checked counter balance and reinstalled dishwasher.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

The entire flat side of the end cap, (with the cutout latch), goes on the outside of the guide bar. It took less than 15 seconds to insert. It took about 30 minutes of searching for videos and playing around with the part to figure this out. A simple diagram would have been helpful.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Took screws out that hold front panel on, unplugged wiring, changed soap dispenser, and put everything back together. Not a bad repair at all.

Reference diagram of upper rack assembly. Remove the top rack (615) from the upper rack rails of dishwasher by unlatching cap ends (652) of rails. Then unlatch and unscrew middle spray arm bracket (620) on old arm spray hub (610) from conduit mid spray (617). Replace old arm spray hub with new one from kit. Next, attach new arm spray mid asm (618) with new bearing spray arm screw (611). Finally reinstall top rack onto upper rack rails and closed latches of cap ends.