PDW8900NW General Electric Dishwasher - Instructions

Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.

The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.

It was sooo easy, I can't believe I took so long to get these new rollers and studs. Shipment arrived in 2 days, I removed those old melted wheels, through them away and installed the new ones, took me less than 10 minutes, it was painless, no tools needed. I did follow a tip from a buyer that was to attach the studs to the wheels prior attaching them to the lower rack and it was a very usefull tip. Do that! Now my dishwasher is like new again. Great shopping experience, Thank you!

We received our parts for our dishwasher within 2 days. It was very simple to find the parts on your site, and very easy to install. Our dishwasher is back to normal and the racks roll in and out easily. I would recommend ordering from PartSelect to anyone.

Removed the existing stud rollers with the wheels attached. Then removed the wheels from the stud roller. Then snapped the wheels on the new "Better Designed" stud rollers. Then easily snapped the new stud roller assembly in place. Piece of cake...works like a charm.

Thanks,

Randy

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

Removed and replaced all rack wheels with new wheels and wheel axles. All I needed was new axles, as they are new and better, and solved the problem of the wheel falling off. G.E. should offer customers with this problem, new wheel axles at no charge, as they are very easy to exchange. The original axle was a bad design.

This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!

but axle on new wheen and put axle on tray

these appeared to be a newer design of wheels and wheel hubs that fit much better and seemed more stable. Very easy to replace and the bottom rack of our dishwasher works great now!

went to sears and was told axles not available ! after they sold my wife all 8 wheels in two diffrent colors. started looking on line found your web site I entered my model number. In a matter of minutes I found the parts checked stock ordered them and recived conformation.
prices and shiping are fair. ordered recived and installed parts in 4 days WOW ! wished all purchases went this smooth.

Von Neal

I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!