Models > PDW8900NW > Instructions

PDW8900NW General Electric Dishwasher - Instructions

All Instructions for the PDW8900NW
61 - 75 of 372
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rollers/clips of lower rack kept falling off due to poor design and improper sizing of front rollers.
The repair was quite easy.
You simply take the new rollers and attach the pins to each of the rollers purchased. I gladly remove the old roller units. I placed each of the new rollers onto each pin of the lower rack unit, and snap them into place.
The rack rolls with ease now thankfully!
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Lower Rack Wheel Dishrack Rollers and Axles - Kit of 8
  • Donna from Burlington, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
128 of 378 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced dishwasher but had the wrong drain hose.
Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.
Parts Used:
Drain Tube Kit CLAMP
  • Victor from Phoenix, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rollers on the bottom rack of my GE Monogram Dishwasher all broke and melted so opening and closing the rack was extremely difficult!
It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Lisa from CHARLOTTE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace rollers on bottom dishwasher rack
Pulled off old rollers and snapped on new ones. Never easier!
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Marilyn from CALDWELL, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one old roller broke
pulled off all old rollers and axiies and snapped on new ones
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Barry from FISHKILL, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Parts Used:
BASKET ASM SILVERWARE
  • Diana from NAPLES, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher not cleaning properly
The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • Melissa from WARNER ROBINS, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower rack wheels kept falling off
delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.
Parts Used:
Dishrack Rollers and Axles - Kit of 8
  • REVERIE from HAMPTON, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ball bearings falling out of the upper dish rack
pulled the end caps, pulled the upper dish rack out. Installed the rear end cap on the right hand side of the inside slider for the rack. installed the bearing and slider in position. Put the upper rack back in and installed the front end caps.
Parts Used:
Cage Roller Bearing Assembly Upper Rack End Cap
  • George from Cincinnati, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top tray would pull out due to stops being worn and missing. Also bottom rack had missing rollers
Removed racks and replaced snap in rollers in bottom shelf and installed new stops in top rack.

No tools needed
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Lower Rack Wheel Upper Rack End Cap
  • Jay from Lynnwood, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wire basket rusting.
The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.
Parts Used:
Upper Dishrack Kit Complete Lower Service Rack Assembly
  • Scott from pleasanton, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser Cap Missing
Ordered new cap and put it on when it arrived.
Simple
Parts Used:
Rinse Aid Cap
  • Larry from Denvr, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak under the appliance
After finding the leak source I have targeted the piece part on your web. It came 2 days after and I replaced the defective part by the new one. I switch off the water, untied the nut to release the pipe, take out the part.
Parts Used:
Adaptor Pump Assembly
  • paul from arlington, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic wheels kept falling off the bottom rack of the dishwasher
The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.
Parts Used:
Dishrack Rollers and Axles - Kit of 8 Dishrack Rollers and Axles - Kit of 8
  • Michelle from Spokane Valley, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing cap
I placed the missing cap into the dispenser.
Parts Used:
Rinse Aid Cap
  • Jean from White Plains, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDW8900NW
61 - 75 of 372
Back to Top