PDW8500J03CC General Electric Dishwasher - Instructions

went online to parts select. Looked at parts that could be leaking. Thought it was the sump. Purchased the sump and the pump connector. Almost bought the adaptor pump assembly, but it was $29.00. Parts arrived in about 2 days. Turned off water and power to dishwasher. Disconnected the copper water line. Hardest part was getting the dishwasher out of space. Once out, layed it on it's side. Parts held together with clamps. Took it apart like a puzzle. Replaced the parts, tightened the clamps. Pump connector hard to unscrew. Got a good hand grip on it and turned it loose. Sump did have a hole in it. Put everything back together. water, electric, etc. Turned it on and it was leaking. Leak coming from the adaptor pump assembly. Couldn't wait 2 more days.Found part at a local parts store for $40.00. Was able to change it by reaching underneath and not pulling dishwasher out again. All three parts needed to be changed. Dishwasher now working fine. If your leaking underneath and taking out the dishwasher change those 3 parts.

pulled the end caps, pulled the upper dish rack out. Installed the rear end cap on the right hand side of the inside slider for the rack. installed the bearing and slider in position. Put the upper rack back in and installed the front end caps.

The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.

Put new basket in, threw old one away

It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!

I placed the missing cap into the dispenser.

The old wheels and attachment brackets were easily removed since they were always falling off. I ordered all new brackets and wheels, but it turns out I didn't need new wheels. If your original wheels are in good condition, they are the same size as the new ones and fit the new brackets. The new attachment brackets are built differently than the ones that came with the dishwasher, but (a good thing considering the originals only lasted 1 1/2 years). The new brackets and wheels snapped together and snapped into place on the dishwasher in minutes--no tools were needed. It took longer to cut the parts out of the packaging than to install them. The bottom rack now rolls out like it did when it was brand new. Definitely worth the few dollars in parts.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.

Slid it in. Very easy and the replacement part is built better than the original part.

Watched a YouTube video on disassembly, parts replacement, and reassembly.

Simply remove broken wheels and clip on replacements. No tools are necessary for this fix and the replacement was inexpensive and easy to install. The kit worked beautifully.

Simple, took five minutes, no tools, problem solved.

1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!

See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.