All Installation Instructions for General Electric Range P2S975SEM3SS

Failed ignighter

Repair is easy. The keeper ring installation while holding the spring down was tricky. An extra set of hands is helpful in holding and replacing the keeper ring.

Parts Used:

Range Electrode Top

Connie from WESTFIELD, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven lamp globe shattered . Needed a replacement

The oven lamp shattered while cleaning. Easy to replace by hand.

Parts Used:

LENS OVEN LAMP

Joan from SOUTHINGTON, CT
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Sparking at 2 different burners all by themselves

Replaced Spark Module and adjusted igniters

Parts Used:

SPARK MODULE

paul from las vegas, NV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bake and convection cycles quit working after a10 minutes

Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.

Parts Used:

Oven Sensor

Stephen from Zachary, LA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Followed a GE Video on installation

Followed GE repair video

Parts Used:

Door Gasket

Sarah from MONTGOMERY, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The electrode had broke

I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.

Parts Used:

Range Electrode Top

O.Robert from Montrose, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

very easy

there were no grate pads so it was easy to add them.

Parts Used:

Grate Foot

ROBERT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Grate Foot

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light bulb went out,could not find replacement part.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

Parts Used:

Halogen Bulb Kit

Gregory from Pearl River, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner cap wasn't working proper.

took burner off installed new one thank you for fast shipping

Parts Used:

Burner Cap

GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.

Nothing technical.

Parts Used:

Grate Foot

Chelagh from Fredericksburg, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven will not heat

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Parts Used: