All Installation Instructions for General Electric Range P2S975DEP3WW

Needed backsplash to complete installation

Installation team. A personal comment--your representative, John, that I spoke with this afternoon was very helpful when I called to question a charge on my credit card statement, and you can be certain that if I have need of an appliance part again, I will think of your firm first.U.L.S. Emory, Texas.

Parts Used:

KIT BACKSPALSH (White)

UrsaLynne from Emory, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Leaking from front door

First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.

Parts Used:

Grate Foot

Gene from Simi Valley, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 of 9 people found this instruction helpful.

Was this instruction helpful to you?

the grate foots came off

put it in but it keeps falling out. they're made narrower than my oven grate.

Parts Used:

Grate Foot

Sandra from Watertown, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Hot Spot On Burner

Replaced old burner element with new, easy

Parts Used:

Burner Head - Large - 12K

Arthur from Riverside, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Replace medium burner for gas cooktop

Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.

Parts Used:

Burner Head - Medium - 9500

Charles from Houston, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Grate Foot Have 8 For My Stove And One Breaks Every Now And Then

This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.

Parts Used:

Grate Foot

Lee from Kenner, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Missing grate foot.

Ordered by phone parts & very pleased with all of transaction.

Parts Used:

Grate Foot

Barbara J from Sweetwater, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Oven temperature was low when reading was correct

First of all, the sensor had the proper ohm reading...at ambient temperatures. I suspected the sensor because it would jump in large degree increments over 200°F. From what I read online, the only other part that would cause this was a faulty circuit board. I opted to try the $20 part first vs. the $200 part. It worked. One screw on the back top of the inside is all that holds the sensor in. Pull the wires out and you will find a quick-disconnect. New part had the same connector (thank you). Thread the wires back through the hole and replace the screw. Works like a champion (verified with an independent thermometer. That is all she wrote. I only wish I purchased two, since they don't last that long... 4 years...or so. I just bought the house built in 2007 and empty for a year... and it took 45 minutes to cook a pizza, and even then the bottom dough was light. A house without an oven is like a hot dog without mustard!

Parts Used:

Oven Sensor

Orion from Vancouver, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Our bottom drawer support broke and the bottom drawer was canted

Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw

Parts Used:

REAR SUPPORT

Robert from Woodinville, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Hard to move drawer in and out because the rear drawer supports broke off.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

Parts Used:

REAR SUPPORT

Steven from Lansdale, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

missing meat thermistor

plug in thermistor when needed

Parts Used:

Meat Probe Thermistor

John R from Asheville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

uneven flame and sputtered, burner was not useable

Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect

Parts Used:

Burner Head - Large - 12K

glen from felch, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The spark module would constantly spark

I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.

Parts Used: