NE6513 Dryer - Instructions

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

did basic diagnostics to narrow down the problem to be likely one of the three parts include w/ the kit. removed front panel and confirmed that part looked like the one on the web page. part arrived 3 business days after ordering.
used nutdriver to remove two screws holding old part in place. pulled old part out still attached to wiring harness and assembled new part and attached wires the same way as the old part. installed new part, plugged in dryer and confirmed that it was heating. replaced front pannel and dryer is now working as well as ever. hardest part was reaching to the back of the dryer from the front while lying on the floor. total cost was cheaper than a service call, let alone paying for parts and labor from a service tech.

Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck

I should have know it was the fuse from the beginning but I figured this out after replacing the the heating coil. (I didn't have the tools to test the wiring, and everyone kept telling me it was the heating coil.)

Anywho, I replaced the thermostat first then the fuse. They were located on the outside cabinet of the heating coil. I plugged it up and then there was heat. They did look a little different from the original ones but you could tell which was which. The fuse is at the top and the thermostat at the bottom. I didint have to use the new wiring to the fuse because they looked fine. I did however had to use the wiring that came with the kit for the thermostat because the old one was fried and a little different from the original.

Well that's my story. Sorry if there's any lackness in the details.

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

I just followed the video instructions and really they were not as good as some of the customer descriptions which were far more detailed. It was like an experienced repairman telling another experienced repairman how he has been doing this repair for 20 years. The customers get into the kind of detail that is very helpful. More important parts select never tells you to read the blogs first before ordering your parts. $100 later I bought a new GE dryer which I would have done 10 days ago had I known Maytag has a repetitive problem with the high limit thermal fuse which no one has a cure for. So I did a whole bunch of repairs replacing parts on a dryer which needed to be replaced.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.

. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.