MLG19PDSAW Maytag Washer Dryer Combo - Instructions

I haven't finished the job yet. I was very surprised and very happy with how fast PartSelect got my part to me. I ordered a lip seal kit (maytag neptune bearing replacement) in the morning, and the very next day it arrived at my door. I'm very impressed. I have everything cleaned up and ready for the new parts. I just have to finish.

Thanks for the speedy service. I'll be highly recommending PartSelect.

Frank

If you are using the newer style seal be sure the taper part of the seal is toward the front of the machine. Installing it backward will ruin the seal and burn up the motor and or controller. The seal installation tool will fit on the side oppsite the taper. It will require a helper to hold the drum support while torquing the nut on the pulley. Better instruction would help too.

The ignitor is easy to determine if it is defective. When you start the dryer and the ignitor does not glow , it is bad.
The replacement involves unpluging the dryer, opening the control access door ,the removal of one screw, unplug the bad ignitor, plug in the new ignitor, reinstall the one retaining screw, plug the dryer back in, check for proper opperation of the ignitor, and close the close the control access door.
Very easy

Removed washer back panel (after unplugging unit). Installed new belt. Reinstalled back panel. Belt wAs very tight getting it to roll onto the drum.

I took out screws holding top to dryer & raised the top & proped it up to gain access to inside of the dryeeer drum. I then inatalled the new baffle & secured it with 2 screws. It would have been better if the part came with new screws.It was hard to determine which was the right screws for this application.

I researched the internet and found my answer on this site. There were others who shared their experiences which made the repair easy. There was a leak in the front gasket between the drum and outer frame. I printed out several answers that customers had posted. I opened the front door on the washer and found a tear in the bottom of the gasket near the drain hole.
To use the washer until the parts arrived (which only took 2 days), I used a bike repair patch to seal the hole in the gasket. NOTE: Don't use the glue type as it may get on the clothing. I used a patch that you pull off the backing and apply. It worked great until I got the parts.
Another party had posted how he got the cable and spring attached on the gasket. He used fishing line. I used masonary string I got from Home Depot. I made a loop on one end and attached it with the spring and pulled both around the gasket after I had positioned it on the back drum. I looped the string over the other end of the spring and pulled. As the spring stretched, I hooked the other end of the cable on the spring. It worked perfectly. Note: Don't worry about the string being underneath the cable, you merely pull it out slowly and the hard part is done. I then hooked the front of the gasket into the slots and finished the job. It took about 40 minutes alone.
P.S. Parts select got my ordered filled and sent to my residence within two days. Great experience and I would not hesitate to order from them again.

Using a screw driver I removed the 4 screws that hold the front panel and door on allowing me to remove the front panel and door. I removed the spring clamp from the drain hose and removed the drain hose. I removed the 4 screws holding the detergent access door on the top and removed the door alllowing me to tilt the top up and back. Now both sides of the seal were exposed. The front side of the seal is easily pulled loose and the back side is held on with a cable and spring tensioner. The spring and cable slipped of freeing the seal. I installed the back side of the seal paying attention to the alignment "ticks" in the seal and washer. I installed the cable assembly and spring using pliers to pull the spring into place. The front edge was pushed into place. I installed the drain hose and spring clamp, lowered the top into place, installed the detergernt access door with the 4 screws, and installed the front panel and door using the 4 screws. The only trick wwas getting the back edge spring tensioner in place. It took 3 tries over ~ 10 minutes. All other items were very easy. I watched the first load wash to be sure the seal did not come off.

Piece of cake. Used flat screwdriver to pry out female part on cabinet side, same with the male part on door. Every new replacement part was tight and operated like new. Thanks Part Select, you'll be forever on my list of online parts buying.

Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of the door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).

Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then he said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.

easy remove the front panel it just pops off unscrew the top and lift up. you have a few pieces to remove then press the old rubber out and install new, i had a little trouble lining up the hardest part was putting the cable ban back on with the spring, i needed help from a friend. now the tub seal was not needed but with it apart I went ahead and changed it the clips were hard to snap on,:you need strong fingers to do that! reassemble as you took it apart. washer works fine no leaks, and alot cheaper than a new washer. thanks to parts select for the right parts MICK KEATING

Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.

Removed one screw and took out old broken door strike, replaced with new door strke and put screw back in. Only took two three days to get the part. The dryer is as good as new!

Taking off the old door and removing the inner door line was relatively easy. I believe I had to remove a total of 8 screws to completely remove the hinges and gain access to the inner panel. Removing the vent tume and grommet was easy, however, I regret not taking a picture of the door latch assembly before removing the vent tube. The door latch is held in by a pair of springs and I had a heck of a time getting the springs back on the door frame assembly. I don't know if I attached it correctly, but the washer locks properly! Attaching the vent tube itself was not that difficult but the same cannot be said of the vent grommet. There was no way to get this grommet in the bottom opening without distorting it or tearing it apart. I finally had to slide it up on the vent tube assembly and basically force it down into the bottom opening. It was not the easiest task to do and I spent more time fiddling about with this stupid grommet than I did with the entire repair. The one thing I would caution anyone doing this repair in the future is to pay close attention to how the speed nuts are installed on the exterior door frame when you go to attach the inner liner. If you do not install them properly you will not be able to attach the inner liner to the exterior door panel.

I replaced the boot seal. I unscrewed and took off the front door and front panel; I unscrewed and removed the detergent compartment; unbolted and lifted up the top panel. I removed the old worn out gasket and replaced the anterior (door side) portion first, then the posterior portion. the door side pushes right in by hand but I used a putty spatula to firmly seat it evenly in place. For ease of closing the spring loaded wire on the posterior portion of the gasket, one person held one end of the wire and gasket in place and a 2nd held the other side in place and pulled the spring with pliers to connect and seal the gasket. replacing the boot seal requires 1 person, but having a 2nd person around to help with the spring was helpful. this was an easy project that takes about an hour.