All Installation Instructions for Maytag Washer MHWE950WJ02

Drain codes

After diagnosing codes noticed no drain replaced pump asm

Parts Used:

Drain Pump Kit

Rohn from Libertyville, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

would not drain

replaced drain pump.Saved 200$

Parts Used:

Drain Pump Kit

Thomas from Bunnlevel, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

F 02 error and the tub would not drain properly. Had some amount of noise when the drain pump was running.

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Parts Used:

Drain Pump Kit

Richard from Lake Jackson, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

pump wouldnt drain

removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install

Parts Used:

Drain Pump Kit

Edward from Dayton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

F/H error

I had replaced the flowmeter, but that didn't solve the problem, so I ordered the hot/cold solenoid fill part. Other than ONE screw that was unique -- the back retaining screws were nut driver screws, the one retaining screw was a torx which, of course, couldn't be seen unless you pulled the washer all the way out. Unscrewed that, unhooked the hose clamp with pliers and worried the hose off, removed the four electrical connections (which were TIGHT) and replaced the part. Turned on the water and was dismayed to get a d/l error code. After some colorful language learned from my drill sergeant 40 years ago, I realized that was "door lock" and closed the door tightly. Ran great and the Mrs. thinks I'm a hero.

Parts Used:

Washer Water Inlet Flowmeter

Harry from Lodi, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

washer weren't drain

Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.

Parts Used:

Drain Pump Kit

JOSE from WOODBURN, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

The Bellow of my washer machine was broken

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Parts Used:

Washer Door Bellow

JOSE from OZONE PARK, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

HF code durring cycle

Removed top of washer and replaced flow meter.

Parts Used:

Washer Water Inlet Flowmeter

lou from stamford ct, CT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

torn bellow

repair was a cake-walk with the video there to help.Thanx

Parts Used:

Washer Door Bellow

donald from Stanwood, WA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set

Was this instruction helpful to you?

Not draining, code FO2

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

Parts Used:

Drain Pump Kit

Monica from Las Cruces,, NM
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Won't spin

Replaced water pump

Parts Used:

Drain Pump Kit

turbo trucking from mio, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

needed to install shipping bolts

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Parts Used:

Shipping Bolt Kit

Anthony from Avon Lake, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Impeller broke on water pump

Replaced pump assembly

Parts Used:

Drain Pump Kit

Washer Bellow To Outer Tub Clamp

Gene from Killeen, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

F35 Error Code Suds

Watched a YouTube video, saw how simple it was. Did all the things the video said to do. Then it said that if the error code came back, by the part. I bought the part SUNDAY night and it was under my door mat Tuesday when I came home from work. Removed three screws, took off the top of the washer, plugged the electronics, shoved the little hose on, put the top back on and boom, no problems! Now, if I could just find a YouTube on a Fisher Paykel dishwasher, I'd be in business... Great part, reasonable price, great service, great shipping.

Parts Used: