MHWE450WR00 Maytag Washer - Instructions

Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip

Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

We read your you tube instruction and followed the video

Removed the old hoses and screwed on the new hoses.

Replaced pump

The plastic tabs were too large to fit into the washer's slotted hole in the washer cage. I initially bought this part from a PartSelect competitor and it was made wrong as well. Whirlpool themselves showed this part on back order so the faulty part originated in a Whirlpool order to a vendor. The reason for this reply is that PartSelect resolved this bad part issue within 2 hours and 1 phone call. The competitor has not resolved anything yet in 3 weeks and 5 emails with image proof.

Unscrewed two screws to remove old faceplate backer. Screwed new faceplate backer to detergent dispenser. Snapped new face plate on to the backer. 5-10 minutes tops.

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

Followed internet instructions

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Removed old valve and replaced it following the directions provided. Then flushed out intake hoses and cleaned aerators. Easy repair. Your directions were very helpful and user friendly!

the tabs were to big on the replacement and the customer representitive said he was unable to help me.

discouraged

I will never buy parts from this site again