All Installation Instructions for Maytag Washer MHWE400WR00

Broken belt

Very easy. Revived back of washer. Used a screwdriver to pull belt over pulley. Very easy

Parts Used:

Frederick from Howey In The Hills, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

washer jumping when spinning

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

Parts Used:

Shock Absorber

WILLIAM from SAINT CHARLES, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Kept getting F2 code and washer wouldn't drain

Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

Parts Used:

Drain Pump Kit

Janet from Sutton, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Sediment clogging valve - E01F08 error code

Shut off water and disconnect hot and cold hoses. Use nut driver to remove three screws at back/top of washer. Slide top of washer back and up to remove. Use pliers to loosen band clamp on rubber hose and pull away from valve assembly. With fingers, disconnect wiring from hot and cold solenoids. Use allen wrench to remove valve assembly from frame of washer. Use reverse order to install replacement valve, although you can leave the top off the washer until you've checked for leaks.

Parts Used:

Washer Valve

Scott from Great Mills, MD
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

My washing machine was not draining

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Parts Used:

Drain Pump Kit

Katherine from Ridge, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Won't spin

Replaced water pump

Parts Used:

Drain Pump Kit

turbo trucking from mio, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Drain codes

After diagnosing codes noticed no drain replaced pump asm

Parts Used:

Drain Pump Kit

Rohn from Libertyville, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

Would not drain..."Suds"

I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.

Parts Used:

Drain Pump Kit

michael from independence, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

F-70 heartbeat failure

The repair went very easy after locating the repair manual inside of the washer. The service manual gave all of the codes that the machine can give. Checked the F-70 code and it stated to unplug the motor control unit. Once that was unplugged the led lights came back on and it acted like it could run again. New unit put in in less than 15 minutes. I'd suggest to have it over nights because the unit I received through UPS was very badly damaged on the outside but plugged it in and it still worked. Two weeks running and a lot of laundry later; still going well.

Parts Used:

Motor Control Unit

Brandon from Angola, IN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

A baffle or "fin" inside the drum fell off

The new baffle simply slid into slots in the drum, took a few minutes to get the position correct but then it slipped right in.

Parts Used:

Washer Drum Baffle

Peter from Bend, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Divider Broke

I just put the divider in the dispencer

Parts Used:

Washer Dispenser Seperater

Susan from Rock Hill, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Door would not close, piece on the bottom of the hinge that pulled door in was broken.

Remove the two screws holding the hinge to the washer body. Lift up on the hinge to remove from the washer. Remove all the screws holding the inner door piece to the outer cover. Remove the old hinge, replace with the new one. Put the two door pieces back together and tighten the screws. Place hinge back in on the washer body and push down. Replace screw at top and bottom. Close door and start using.

Parts Used:

Washing Machine Door Hinge

Larry from Gardena, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

washer weren't drain

Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.

Parts Used:

Drain Pump Kit