All Installation Instructions for Maytag Washer MHW6000XG2

Broken Strike on Washer Door - prevented door from latching, and washer would not start

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

Parts Used:

Strike

David D from Severn, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Se rompió la bisagra

Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio

Parts Used:

Hinge

Isaac from SAN ANTONIO, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Washer was filling up with water when not on or running.

Removed old valve and replaced it following the directions provided. Then flushed out intake hoses and cleaned aerators. Easy repair. Your directions were very helpful and user friendly!

Parts Used:

Washer Valve

Judy from Sagamore Hills, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replacing the heat sensor following an F-24 Error Notice.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Parts Used:

Washer Temperature Sensor

william from VIRGINIA BCH, VA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replace tub to pimp hose.

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

Parts Used:

Washer Pump Hose

Bob from LORAIN, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Water leaking on floor from door

Watched this video on the website and went to work. Went very easy and smooth with removing the door. A pair of pliers works fine for outer ring. Kind of challenging by yourself, but I got it on in less than 5 minutes. Pliers in one hand and flat head screwdriver in the other to work the ring on. Much cheaper than paying someone to do it. 2 out of 10 for difficulty.

Parts Used:

Front Load Washer Bellow

Jeff from Spring Lake, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem

I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.

Parts Used:

Dispenser Actuator Switch

Martha from Pine Island, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Door would not lock

Did the repair just like the video on your website. Was really easy.

Parts Used:

Washer Door Lock/Latch

Michael from Tonawanda, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Washer would not fill

replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.

Parts Used:

Dispenser Actuator Switch

Steve from TULSA, OK
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken hinge on door

Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.

Parts Used:

Hinge

HARRY from OZONE PARK, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Front legs were rotted.

Replace front legs. Very easy fix.

Parts Used:

Washer Front Leveling Foot

Cindie from DUNMORE, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable), Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Old hot water inlet hose had budge at both ends.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Parts Used:

Inlet Hose - 5 FT

Jimmy from MEMPHIS, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bought a washer without front leveling feet

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Parts Used:

Washer Front Leveling Foot