Models > MH9115XEB0 > Instructions

MH9115XEB0 - Instructions

All Instructions for the MH9115XEB0
61 - 66 of 66
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old filters were beyond cleaning
Simply removed front of Microwave, removed the old charcoal filer and inserted the new one. On the grease filters, removed both of them from bottom of microwave and slid the new ones in place. That's all there was to it. No tools required.
Parts Used:
Charcoal Air Filter Grease Filter
  • DAVID from ST. SIMONS ISLAND, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Parts Used:
Light Bulb - 40W
  • Lester from Mesquite, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave worked intermittently
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.
Parts Used:
Door Interlock Switch Kit
  • Robert from Palmer Lake, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
2 burned out bulbs under the microwave/important light source for kitchen stove.
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.
Parts Used:
Light Bulb - 40W
  • Ferol from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace old parts
remove one screw from light and remove bulbs replace. I found the light plate had a lot of grease on rubber type washer for the glass cover. I cleaned it as best I could. The real trick was putting the screw back in when the Microwave is in with the hood Fan and the screw must go straight up and not miss the hole. I had someone hold the plate up and the screw went in. Your instruction book shows your filters and how to clean them. They are easy to and clean. What I found best is the lights they had been in for 15 years and the new ones are so much brighter. I now have an old set of filters that can be put in the dishwasher and used as a replacement when the new ones need to be cleaned.
Parts Used:
Light Bulb - 40W Charcoal Air Filter Grease Filter
  • Thomas N from Maidens, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor quit working but light and timer still worked.
Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.
Parts Used:
Door Interlock Switch Kit
  • Thais from La Grange, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the MH9115XEB0
61 - 66 of 66