MFI2570FEZ13 Maytag Refrigerator - Instructions

take the old one out replace with new once - no instructions required, no tools needed

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

Removed old gasket by carefully pulling it out of the retaining groove. Installed the new gasket starting the corners first and then seating the upper and lower straight portion gently in the retainer groove. Total time for installation was at most 5 minutes. After a week no ice or frost has been found along the bottom of door or freezer. Note: the new gasket came in a small box for shipping purposes and the new gasket was twisted in a v for this purpose. Upon arrival, I laid it out flat on table overnight so it could cool to room temperature and straighten. I would recomend this procedure for a perfect installation.

Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!

After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After replacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.

Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)

Took out the old and installed the new.. The fit was perfect.

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Unscrew filter. Screw on filter bypass

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.