MER8700DS1 Maytag Range - Instructions

pulled the old gasket, the new one fitted perfectly. No effort at all.
An instruction sheet would be a bonus. I wish you put instruction sheet in all parts OR a web link for video instructions. a web link would be great

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Followed a video I found online showing how to replace the bottom bake element. It was very easy to do. I simply unplugged the over, removed the back wire cover and detached the damaged element connectors.

I then removed the bottom oven cover which conceals the element. Unscrewed and removed the damaged element and replaced it with the new one. Connected the wires to the new element and then Installed the bottom cover along with the back wire cover and plugged the oven back in. It was really this easy.

I've replaced oven heating elements before, but never in a 3 year old electric range oven. I watched the video again after the element arrived, and installation was easy with only 2 screw drivers. I was concerned about the repair when I saw the severity of damage to the old heating element and the underside of the bottom oven metal/ceramic plate, which was almost burned (a hole) through. After finishing the installation the oven showed it was preheating but no heat was being generated. A couple of phone calls later, a Whirlpool repair technician told me the main control panel needed replaced- $385 much higher cost due to chip shortage, inflation, and would take 2 months to arrive due to supply chain issues. So I don't know yet if the element is good or not. I am disappointed that the element blew in a relatively new appliance, but a total cost of $600 in a 3 year old oven is still probably better than $1200 for a new oven which is double the price I paid in 2018. Part failures never come at a good time but 2 months without an oven at Christmas & New Years is added frustration. When the heating element burned out there was a loud buzzing sound associated with the failure, which I've never experienced before and there were flames coming from underneath the bottom plate in the oven for an extended period of time. The repair for the heating element itself went smooth, but be advised you may get into more than just the element.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Watched video & did just guy in video did. Very easy job & the burner works like new.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

1. Pull the stove away from the wall and unplug the stove from the 240 volt receptacle.
2. Remove the knob from the switch (it just pulls off).
3. Unscrew the top half of the back plate of the stove and removed (about eight or so screws).
4. Unscrew the two screws attaching the control switch in the front of the control panel (these were hidden by the control knob just removed).
5. Pull out the control switch and detach one at a time the two sets of wire connectors attached to the switch. In order not to confuse which plug goes where, attach each connector to the new switch as you remove them. (Note: the connectors may be quite tight to the original switch; do not pull on the wires but simply work each connector gently until it slides off. They will reattach to the new control switch much easier.)
6. Reinstall the new switch to the stove in reverse order of removal. Make sure that the control knob, when the switch is reattached, is in the off position pointing straight up.
7. Reattach the upper back plate of the stove. For safety's sake, do this before reconnecting the stove to power.
8. Plug in the stove and test to ensure that the switch is working properly.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

First, I shut off power to cooktop at breaker and double checked to make sure. Then I disconnected wiring and exhaust duct since the cooktop is a downdraft. After that was completed, I had to remove control knobs simply by pulling straight up. A neighbor helped me to lift the cooktop from the cabinet. After stabilizing the cooktop, I removed the hex nuts holding the glass in place. Then the glass lifted off easily and I could access the bad element. I took pictures of the wiring before disconnecting the wires and installed the new element. Then I reversed the procedure to put the cooktop back in the cabinet, reconnecting the electric and exhaust. I flipped the breaker back on and the element was just like new...because it was!

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Very easy followed instructions from a youtube video.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.