MER6775ACF Range - Instructions

Two screws loosen the cook top so you could get to the six (or was it eight) screws underneath the cook top. Once those screws were out, three more screws were removed to take off the element. Disconnected a couple of wires and the old element was free to be removed. The new element went right back in and screws were put back in reverse order. Less than ten minutes from start to finish.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new element and screwed it into place.

Removed screws, pulled out element, disconnected wires, connected new element and screwed it in. 5 minutes tops. Best part is I ordered the part on Tuesday afternoon and it arrived Weds.... great company, Thanks!!

Well all that was needed was to remove the two screws that held the element to the frame. I remove the screws and the two connection from the element. PLUG N PLAY. It's working and my wife is happy.

Removed bottom and side trim, slid the bottom trim onto the glass, and reinstalled the glass on the door. I think there were less than 8 screws total.

easy to put in

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

First we loosened the oven handle which required removing 4 screws. Then we removed the bottom piece which the glass sits on which required removing 5 screws. Placed the double stick tape on the frame then placed the glass on. We then put the bottom piece back on, tightned up the oven door handle and we were done. lrss than 1/2 hr later. This dose take 2 people to do otherwise you might drop and brake the glass. One thing I will say is that the oven glass did not come with the double sided tape to don't forget to order it. Also, there is only 1 piece of tape per package so order the proper amount your oven requires.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Removed the door form the oven. Removed all screws holding the door covers. Removed all screws holding the handle mounting brackets and handle. oriented the new handle to the door and reversed the disassembly process.

I pulled the range away from the wall to gain access to the back.I turned off the power to the range at the circuit breaker panel. I unscrewed all little screws on top of back plate then removed it carefully.I took several pictures on the connections to the ECR board.I watched a video on You Tube which was helpful.The difficulty was getting the connectors off without breaking them. By carefully putting the edge of the flat blade screwdriver under each connector and twisting it gently I was able to get this little plastic locking pin to let go.Once this pin unlocked I was able to remove the connector from the prongs on the range. After removing the ECR board I carefully removed the decal from the front of the old board by pushing the edge of a sharp putty knife slowly under the decal. Following the pictures I took I was able to connect the new ECR board connectors properly and re-assemble the board into the top of the range after attaching the decal being careful to line it up properly.Once the range was back against the wall I turned on the power and set the clock then proceeded to test the small top oven which now worked fine.I found the people at at this stie to be very knowledgeable about what parts are needed to fix common problems.

Removed 2 phillips head screws, disconnected the 2 wires. Installed new element, connected wires then installed screws. Took less than 3 minutes. What i liked was how fast I received the new element. Ordered online on Friday around 12:30 and received Saturday morning by 9:00 AM. Excellent transaction!