MER6755AAS26 Maytag Range - Instructions

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

IMPORTANT NOTE: This element is shaped like a B. The straight line part of the B, which is closest to the back part of the oven, doesn't light up. At first I thought it was a defective part. My husband is the cook and I never realized this. This fact isn't indicated in the instruction booklet which came with the oven. My sister has the same oven and she didn't realize it doesn't light up either. I looked up installation instructions on You Tube and although I was very nervous, it was easy to install. It's a little awkward because the wires are in the back of the oven so have a flashlight handy.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

Bought new hinges as that was the obvious problem.
Below is the removal, installation process for new hinges. Turns out in my case there was nothing wrong with the hinges. Problem was still there after installing new ones. I found that the metal in the door that butted against the hinges was fatigued causing looseness. I ended up compressing the metal back into shape with a hammer. Problem solved but money wasted on hinges.
If you replace hinges. Here is what I did.
1. Open door slightly to where it stops in broiler position.
2. Remove the door by pulling up.
3. Remove two screws in front of hinges that hold them in.
4. Pull range out a few inches for access the remove the side fillers that trim out the stove.
5. Reach in from the side and work hinges out.
5. Pop in new hinges and reattach the 2 front holding screws and the side trim screws.
You are done.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

• Removed the oven door (pulled right off old hinges)
• Removed two screws
• Removed broken hinge
• Placed new hinge in place
• Replaced screws
• Replaced oven door.

pull oven out and Un-plug oven remove screws from back panel , un plug wires from old heating element. open oven door and remove the two screws that was holding the the old heating element, pull it out . Install the new heating element and replace screw. plug wires to the heating element in the back of oven. Replace back panel. plug oven back in. and test

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

I removed the two screws, puled out the element and took the pliers to unhook the two wires.

First I unpluged the range from the power source. Then I removed the back cover, disconnected the two wires to the element, remover two screws on the inside of the oven the held the element in place and removed it. I then installed the new element in the reverse order. This took about one day to get the new part and 15 to 20 mins to do the repairs. I figured that I saved at least $55 on a repairman service call.

remove two screws, remove two slide on wire connections and remove element. reverse to install.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.