MER5770AAW Maytag Range - Instructions

Turned the power off to the oven, unscrewed the ends of the element, connected new element, screwed it back in to place and turned the powe back on. The video provided in my shipping confirmation was very helpful.

Unscrewed ceramic stove top , lifted top and exposed element , unscrewed element from top and disconnected wireing (marking wires to assure proper reinstillation .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new element .
Replaced top on stove and rescrewed to secure .

replaced burner by following the wiring from the photo we took. worked god except was cooking to hot and would not cycle. went to use my smaller burner in the back on the same side and the center of the double came on. so we watched another video looked at what we did wrong with the wiring. here we wired the burner slightly wrong we did not follow the numbering. this time followed the numbering and all is good. burner is working good and cycling.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Watch the video. Spot on instructions. Easy peasy.

My genius scientist husband responsible all electric string connections, I responsible buy right parts and all support work, we worked as a team and fix the problems:) :)

The replacement unit was a substitute part. Wiring slightly different. Instructions bare minimum. Follow instructions and it does work. No instructions as to how to remove the stove top. Been there before so sort of knew how. Nothing in the Jenn Air manual for stove top removal. The control panel has to be removed, two screws on each side and four hex screws on bottom, this allows for the disconnect of wiring for the top.
Remove the two trim pieces one on each side. One screw at top and one at bottom. The trim piece will move towards the rear and come off. Two screws on each side and two in the back will release the top. Remove top and lay on padded surface. You are ready to replace unit.

Removed front panel of range, removed switch (2 screws), unclipped wires from back of existing switch. Installed new switch - reverse order of above.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.