MER5552AAS Maytag Range - Instructions

Unplugged old burner,plugged in new one

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.

after finding my part and thank god for you guys i recieved it early it only took 4 days to get here i unscrewed my old oven part and popped the new one in easier than making cookies and now i can bake til my hearts content thanks for being there for me
barbara krebs

I took the broiler pan out of the shipping container and put it in the oven.

First, turn off the breaker to the range. Then just remove the 2 screws that hold the element at the back of the oven. Pull the wire connectors apart or push them off with a regular screwdriver. Instructions that I read said to make sure the wires don't fall back through the holes, but in our case the insulation held them in place. Reconnect the wire connectors to the new element and reattach with the screws. Easy!

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.

Turned off power to oven. Removed screws from each side of element. Removed connectors to disconnect old element. Connected new element to connectors. Replaced screws, then turned on power to oven. Turned on oven to heat. Easy install.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Looked at parts blow-up, watched a You-Tube video,

Had to remove 4 small rusty screws and a sort of guard made of metal. With power off, I had no light to see way in the back of the oven. Suggest use of a head-lamp.
Also, it would have been very helpful if when the part arrived, it was noted somewhere that a smell and “smoking” from the part is very normal. This would have saved me a tremendous amount of stress and more days without the broiler trying to figure out if I did something wrong, if the part was bad or other. Sounds so simple, but BOY, that would have been SO helpful