MEDB725BW0 Maytag Dryer - Instructions

Found this website and reviewed videos and comments prior to purchasing the heater element and high limit thermostat and thermal fuse kit. We had recently put our Whirlpool duet washer and dryer on pedestals and after that, the dryer would come on and run, but would not heat up. Installation of the parts we ordered was simple...and we would be considered novice installers....really great website and easy to understand. Customer service was excellent as well. After installation of the parts, still no heat and heating element was registering only 120v. We checked everything again and found that the dryer plug was not all the way in the socket. Probably came loose with the move to the petestal.....plugged it in securely and it works great now. Should have checked that first, but because it was running we just didn't think of checking it. Good lesson learned and so glad we found this website. We will definately be using this site again and telling everyone we know about how great you guys are! And at least we won't have to worry about the dryer for a while and we now know we can fix a dryer that won't heat up!

once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!

Took the old filter out and inserted the new one- works great!!

Remove bottom panel was able to remove the element from the bottom without taking off the whole front and removing the drum simply remove the panel remove the two wires connected to the coil unbolted the bracket that was held on by two small bolts then removed the 4 bolts holding the bracket together was able to remove the heating element and then put everything back together did not have to remove the drum the top or the back panel To complete the repair I am not an appliance repair technician just a homeowner but I was still able to repair this myself and it’s working just fine

Very bad design to keep door shut but very simple to fix. Just screw bad strike out and screw new one end. Whirlpool should have gave extra when you buy this type dryer.

Pulled out the old and slid in the new filter

My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you

I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. Also, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.

Like another reviewer's repair story, I decided to take the door apart. It was too difficult, at least for me, to get the faulty catch out without damaging either the the door or my hands. This is why I give it an "easy" rather than "very easy" rating and put the total repair time at a half hour or better. I also decided I wanted a second person to help - not with getting the door apart or putting it back together, but because a second pair arms was very helpful in rehanging the door well. We removed the door (four screws), marking which side of the hinge needed to be flush with the actual dryer when rehanging. Then we took the door apart, which comprises another sixteen screws (four on each edge). We used an electric drill but I'm sure it could be done manually. We used needle nosed pliers to get the faulty latch out of that side of the door, then replaced it with the "back up" from the other side. Then we put the door back together and carefully rehung it. Done. We did decide that, in future, all kids (we have three boys) slamming the door would be severely beaten. Pushing the door until it's against the dryer, then PUSHING (as opposed to slamming) the latch ONTO the catch pin on the dryer is obviously what was intended. However, I've learned not to count on my boys being particularly conscientious, so I'd ordered four replacement latches to keep on hand. This machine was delivered in April 2009 and I replaced the latch in April 2011. Based on this and our laundering habits, I'm sure the others will be used long before the dryer calls it quits.

Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.

Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

very easily