MDET446AYW Maytag Dryer - Instructions

I removed the dryer front and replaced the door switch.
Next I replaced the drum glide reassembled the dryer.

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

The video on the web-site was very helpful in showing how to take it apart. First we remove the power plug from the wall outlet. Then we used flat scrapper to push the top two hidden clips to release the Dryer's top. We used the nut driver to unscrew the two screws that held the front panel. We carefully remove the wires that were connected to switch sensor for the door, and the lights. Next step was to unscrew couple more screws that held the front piece from the main fan housing. At the bottom locate the tensioner of the belt. Release it. Remove the dryer drum with the belt. We took the opportunity to clean off the lint that was all over on the bottom of the dryer. We then could reach the bottom left back of the dryer to unscrew the screws that held the heater unit. Before that we unscrew and release the wires for the Thermal fuse and the limit thermostat which are all located on the heating unit. Then we replace with new pieces. Upon removal of the heating unit we noticed the broken heating element. Next was to place the drum back in. We made sure that the drum lined up with the rear support piece then the front. We rotated the drum just to make sure that it was sitting correctly. Then we screwed the front housing unit. Then we put the front panel back on the hooks at the bottom. That help to line up the front panel with the main chasis. We connected all the connectors to the right terminals. Last was to set the top down on to the chasis. We checked that the duct in the rear is not obstucted. Lastly was plugging in the power cord and testing the dryer. It is working again. Thanks to Part Select's video and parts. Total time was just over half an hour.

A friend did the repair for me. Very simple. Saved me a lot of money by getting the parts and fixing the problem. Thanks!

Pull broken knob off, push new knob on.

unpluged the dryer,and removed the top.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.

then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.

I took out the old worn out part and replaced with the one I order.

Researched problem on line. Many others had same symptums after power outages and Hurricane Irene. Dryer was in use when power went off, back on, back off than on again. Dryer would not work more than a few seconds. LED lights would go off; Drum did spin; Heater elements came on. All symptoms pointed to the control board. Replaced board and dryer is working now. Reports state that this particular control board is very susceptable to power bumps and will fail.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

No problem