MDB7851AWB10 Maytag Dishwasher - Instructions

take handle off old basket put on new basket done

I bought 2 Maytag appliances, a microwave and a dishwasher - they are both crappy!

The top plastic spray arm kept falling off into the top shelf of the dishwasher, causing all of the glasses on that shelf to come out dirty.

The arm has a small bracket that can snap off and on the main water tube easily without tools.

Changing it was a snap!

The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.

Having utensils falling through was really getting old. This was $25 well spent.

I removed the screws around the top and halfway down the sides of the inside of the door. I found that you dont have to remove all 10 screws to access the assembly. Reach in and pulled out the assembly, there was enough slack to pull it out above the door. Pull the connectors off and slide the new ones on. Set the new assembly back in place, insert the 2 top screws first, and then the rest. That was it...very simple to change.

Replacement basket did not include handle so needed to pry old handle off broken unit to use on the new one. Used screw driver to pop loose clips which attached to basket. Had to stick tooth picks broken in half under them to hold out until all four clips were opened at once - then handle could be pulled off. Easily snapped it back on to the new basket and repair was done. Can't get any easier than this!

Removed ~12 screws holding the inside liner onto the door. Pulled off the two connectors (one with black and one with white wires). Replace the handle and latch mechanism. Redid connections and replaced screws. Viola. (Be sure to buy BOTH the handle and latch mechanism- I don't see how you could easily install the handle on the mechanism myself, and what broken in my case was the black handle).

seeing as how my husband was out of town, I inserted a regular flatware knife in each of the four slots that held the handle in place on the basket. I then slowly pushed down on the handles of the knives on opposite sides of each other to unlock the handle from two slots on the basket and then went on to push down on the other two flatware knives on the opposite sides...sure enough, the handle came right off...less than 5 minutes in all to take the old handle off from the old basket and then snap it into place onto my newly acquired basket.

Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.

Removed the old one....slid in the new one.

I took out the racks and disassembled the bottom assembly until I got to the impeller. Just replaced the part and reassembled. I used only a star shaped driver on all tightened pieces. It was very easy to do and I did not even need any advice/help from the hubby! Saved a whole lot of time and money doing this small repair myself. Thanks for fast service. I ordered part online Thur. late afternoon, and it arrived Friday.

da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit

first, i removed the inner door panel exposing the latch assembly. i then disconnected the wiring to switches noting their locations. removed and replaced with new latch assembly, connected all wiring back to their corresponding switches, assembled the inner door panel and checked to make sure the latch was working properly.

After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.

Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.

For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.

Must say my wife was very happy to have the dishwasher up and running again.

Good luck !

Ensure to order part # PS1559543, which is the complete assembly although the diagram doesn't show this, and not PS2100626 which doesn't include the handle. The new assembly is a different style than the original therefore you should replace the complete assembly.

This was an easy fix. Remove the eleven torque screws on the door and separate the inner door panel enough to remove the old assembly. Remove the wire connections from the door switches, reconnect to the new assembly, and reinstall the assembly and inner door panel.

First, shut off the circuit that the dishwasher is on. Remove the 10 - 12 screws that secures the inside waterproof panel to the door. There are two electrical connections are either side of the handle (latch assembly) that need to be removed. No need to disconnect any other connections or reservoirs. The handle comes right out. Seat the new one in door front opening. Reconnect the electrical leads and reseat the interior panel. I would put in the 2 screws are either side of the handle first; then the 2 at the bottom on either side and then the remaining. This is a very easy DIY job.