MDB7601AWS41 Maytag Dishwasher - Instructions

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

You just remove the old unit and set in the new unit. the wheels were already connected.