MDB6601AWB46 Maytag Dishwasher - Instructions

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

I originally ordered the incorrect piece via the website, however when calling PartSelect to return the part they informed me that they could help me find the correct piece which they did. The correct piece arrived within 4 days. It was easy to install. The part works well. I'm very happy with the customer service.

Removed 11 T20 Torx head screws. Removed and replaced latch. Removed and replaced door seal and foam insulation strip - no additional tools required. Super easy to repair and didn't leak a drop afterwards.

Followed the suggestions on PartSelect - took off the screws on the door; removed 2 screws on the assembly that held it to the door; disconnected switches (hardest part) - they seem to fuse on(or rust) from the moisture; took the new (much sturdier part than original) assembly and plugged in the switches; set in place; replaced the 2 screws, replaced the screws holding the door panel - Complete - works great! Here we thought we would have to get a new dishwasher!!!!

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

I removed the old door seal -- it just slips right out. Then I inserted the new door seal. One thing I noticed on the old door seal and also in your photograph is that the last inch or two of the seal on both ends is kind of sliced in half perhaps to make it fit better in the corner. But we decided not to cut it yet and have been using it uncut as it arrived in the package. It is working great! No leaking! So we're not going to cut it. Thank you for offering this great service. It saved us a lot of money since we didn't call a repairman.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

Took the new part and ran silicone around the opening for the ribbon cable to prevent steam from entering shock I believe causes this unit to constantly fail. Install the part. Then ran another bead of silicone around the touch pad to prevent water from entering. Hope this stops this unit from failing