MDB3100AWE Maytag Dishwasher - Instructions

I used a voltmeter to see if 120 volts was present at the right time in the cycle; it was, so the actuator was the likely culprit. I ordered one on a Monday afternoon about 2:30, and it appeared on my doorstep Tuesday, shortly after noon! It took less than 15 minutes to replace the actuator - removing the 7 Phillips-head screws, lifting the panel, popping out the upper actuator, removing the two wires, putting them on the new actuator, popping it in and putting the panel back on. Worked like a charm. Happy wife . . .

Pulled out the old gasket and pressed in the new one. No more leakage.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.

Took out the old basket,
Threw it away.
Popped in the new baskey,
filled it with forks and spoons.
Works great!

By the way, my order arrived in one day.
Phenomenal!

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

Lifted out old silverware basket. Set new basket in. Took approximately 20 seconds.

Determined that I needed a new door switch. Bought it, then opened up the door by removing the inner panel with the six point screws. Removed one inner panel with a nut driver. Located the old switch, and wiggled it out of its mounting location. Used my Swiss Army Knife screwdriver blade to pry off the electrical connections. Plugged in the new switch, and wiggled it back into place. Replaced the inner panels. The dishwasher now works again.

Just slide the old upper dishrack forward to the end. The stops on either slide must be removed . Only difficulty was getting the plastic stops to open up. We used a thin metal knivre to wedge into the opening.

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

held spray arm to arm connector and replaced snap retainer, works like a new machine

Actually following the online video is the way to go.

remove damaged retainer clip. Install new one. Note: the upper spray arm screws onto the ceiling of the dishwasher with a reverse thread. That is, you need to turn it counter-clockwise to tighten it.