MAV8600AWW Maytag Washer - Instructions

Opened the lid and snapped hinge in to place. The part was an exact match and the job went flawlessly.

I popped off the fabric softener on top of the agitator. Used an extended arm on my socket set to remove the only nut holding the agitator on the motor assembly apparatus. The agitator came off with ease. Just reversed the procedure in replacing the new agitator. This was an easy job.

Part Select data showed that over 60% of the time, this issue of the washer shaking was due to broken support springs for the tub and over 30% of the time, it was a worn/broken snubber ring. So, I initially purchased the six springs and snubber ($30 total) from this site and completed both of those repairs. I leveled the washer securely and tested it again. However, the washer still had the issue of shaking during the spin cycle with no improvement. So, I then researched again for this issue and parts recommended were a lower bearing kit or transmission. Since the transmission replacement was $429, that wasn't worth trying. So, for the $52 lower bearing kit, I ordered it from along with a new belt ($22) (even though the existing belt didn't show any signs of significant wear, but I changed it anyway). The new bearing kit was installed and the washer is now operating like new. I used the current videos on the website for replacing the parts that I ordered, and they were perfect step by step instructions. It made the repair very simple for anyone with any sense of do-it yourself ability and with minimum, ordinary tools. So, for approximately $110 for parts and doing the repair myself, the washer is like new again. Thank you!!!!

As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.

I also really like you list of probable solutions to the problems with the machine.

My wife is now happy with her washer again therefore I am also happy.

Thanks so much.
I can see me being be a loyal customer for many years to come.

I watched the installation video. It was very helpful to see it done before doing the repair. I followed the video to take the old springs out and installed the new ones. Remember to check the snubbed ring and replace it too. The new springs and sunnier ring solved the banging and moving during the spin cycle. Now the washer is like new and the repair was less then $100. Thanks parts select, the help was greatly appreciated.

There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Removed the old hoses and screwed on the new hoses.

I followed the direction came with the part.

• I unplugged power electric wire from the wall.
• Unscrewed total of five screws from the back of the top console.
• Removed the top console to gain access the switch.
• I took pictures of the switch position for a future reference.
• Unplugged the switch wire by just pulling the plug.
• Carefully removed the switch and pulled the plunger out plunger assembly.
• Entered a new plunger in first and inserted a new switched carefully.
• Opened and close the lid few times to check the switch is going on an off properly. You will hear clicking sounds.
• Plugged the switch wire to the new switch.
• Reinstalled the console and screwed back the five screws.
• Plugged back the electric plug in wall outlet.
• Tested the washer by washing a full load of clothes.

The whole process took me about 30 minutes.

-Abhay

Took the back plate off, popped the old lid switch out and the new one in. Very easy. No problems, saved $100 buck at least doing it myself.

very easy replacement. was probably broken for a year and only took five minutes to replace. Can't believe we waited so long!

Took off the upper back that had 6 screws with a screw driver. Found the lid switch . Removed it after I figured out how to remove it. It was a little tricky without instructions. Putting in the new switch was a little tricky also. You have to angle the front of the switch in, pop it in and then push it back so it can snap in. Once I put it in, the washer started right up. I was very happy. Instructions would have been very helpful. I am very pleased with this company because I received my switch in a couple of days. I will definitely use this company again.

Removed the old part with a screwdriver & installed the new part. It took approximately 2 minutes.

Removed front panel also right side panel to get to the springs. Used vise grips to extend springs and used coins to keep springs open for replacing.