MAV6250AWW Maytag Washer - Instructions

Removed the old hoses and screwed on the new hoses.

As for how I did the repair , I just followed your instruction video . The instruction video provided by Part Select was very very valuable.
The snubber ring was a piece of cake BUT would have been really difficult without the helpful hints in the video like replacing three of the screws in the rings collar with three longer screws so as not to disturb the spring under it.
The suspension springs were a bit more trouble since my washer doesn't have an access panel on the back however THANKS TO YOUR TIP to stretch the spring and put coins between the coils made this much easier . I don't know many guys that are strong enough to lay down and reach through the front and put those springs on the back.
Of coarse the belt was easy.

I also really like you list of probable solutions to the problems with the machine.

My wife is now happy with her washer again therefore I am also happy.

Thanks so much.
I can see me being be a loyal customer for many years to come.

I watched the installation video. It was very helpful to see it done before doing the repair. I followed the video to take the old springs out and installed the new ones. Remember to check the snubbed ring and replace it too. The new springs and sunnier ring solved the banging and moving during the spin cycle. Now the washer is like new and the repair was less then $100. Thanks parts select, the help was greatly appreciated.

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!

There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

We had a repair guy come in and he said fixing the pump would cost at least 250. I called my dad and he walked me through it over the phone. I took off the back of the washer, and laid the washer on it's side. I then had to take a break as I had flooded my kitchen. (Lay the washer at an angle.) The belt was taken off by the repair guy. I then undid the hoses, taking the clips off with pliers. Next I screwed the new pump in, and put the hoses back on. FInally I took the belt and stretched over the two small pullies, and then pulled it to the bottom of the big pullie and started spinning it until it wrapped itself all the way around. It wouldn't have taken over an hour but I had a baby who needed me ever couple of minutes.

1 I opened the top of the washer found the top plastic rim piece broken due to the fact that it cracked while unbalanced one time. Which made it leak which ate away the rubber seal . The parts were here fast and they were the right ones. Great job and I will tell everyone about you thank you verry much.

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!

This was a very easy fix.....roll belt off....roll new belt on....seemed to help not sure if it fixed problem....might try pulley and bearing kit next

I popped out the hinge pins, popped outthe busshings, popped out the cam. time less than 10 minutes, pressed in the limit cam, pressed in the bushings, pressed in the hinge pins. time about 5 minutes. the most important thing is my wife is extremely happy. I'm happy the parts fit perfectly.
also the parts arrived in 2 days.