MAT14PDAGW0 Maytag Washer - Instructions

Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

Removed the control panel and the cabanit. Then removed the adjutatior . Removed the motor and gear box slid the old shaft out and put the new one in put back together. Took about one hour .

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

We search on line the possible cause for our problem and Partselect offered the possible cause and solution. We watched the video on replacing the water pump.We then ordered the pump and 2 hoses.We followed the instructions and after removing the front panel, we found out one of the pump retainer was rusted away. We tried to look for local supplier and was shock that Sears was charging 20 bucks for a single retainer, which Partselect only charge dollar and eight cents. We ordered the 2 retainers on Thursday and it arrived on Saturday afternoon. We were able to fix the problem and are very happy there was no more leak. I wish the retainers come with the pump even if you include the extra cost to the pump pricing. We could have save the extra shipping charge for ordering the retainers only. I would definitely order more parts from Partselect and recommend it to my friends. Thanks again for your help.

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.

After removing the front, sides and top of the machine (all one piece) the springs were relativley easy to access. I discover one of the brakets that held one of the springs had rusted and would no longer support the spring. I then replaced the bracket and springs. I Re-assyembled the machine and it work as good as new.

Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL

Watched the video on your site for that part

Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

followed repair instruction,( bought on line and down loaded ) some instructions were unclear but when you have the machine apart its obvious. your parts breakdown helped more than the instructions once the cabinet was opened.

Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!

Replaced broken and worn wear pads per online instruction.also replace tub springs and counterweight spring.all very simple.

Since I had taken the washer apart before to find the problem, it was easier to remove the cabinet.Four screws and a electic connection. I remove the cabinet to get to the balance ring.I removed the tub ring by releaseing the catches and pried off the ring. Installation was just the reverse. Had some trouble putting the cabinet back whereit needs to be but once I got it the rest of the job was easy.