MAT14PDAGW0 Maytag Washer - Instructions

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

First need to remove cap on Agitator. Inside there is a washplate bolt. Remove bolt. Old Agitator will slide up. Pull washer off stem. Clean grooved stem very well. Use some sort of lubricant on stem. Slide new Agitator on to stem. Part will be very snug as metal and plastic do not mix well. (Lubricant needed) Use board to lay flat on top. Gently tap with mallet until fully seated. Install new bolt. Run test wash. (Helps clean wash tub from any foreign substances.)

Disassembled top control console and surrounding sheet metal cabinet per the video from this site. i then used a screw driver to carefully pry up each wear pad location individually and inserted the wood wedge. to about 1 1/2 inch height. rwmoved the old wear pads and popped in the new pads one by one. Closed up the unit and tested the machine . It ran like new. No more noise or viberation

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

Tried to follow videos. Couldn't figure how to raise top. Laid machine on front used pliers to unclip bracket and clips holding hose. Took 10 minutes to work it this way.

Old machine and vibrations are still there but weaker. Seemed to turn counter clock wise. Put a 4x4 board behind in order to stop the twisting, and keep hoses safe from vibrating and causing wear. Stays fairly stable now.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast