MAH14PDCBQ Maytag Washer - Instructions

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

The instructions from Richard of Austin, MN were instrumental in repairing my clothes washer. I am an electronics technician, and my control board failed just like Richard indicated. One thing Richard did not state is that resistor R11 and Q6 did not fail until the wax motor (solenoid) shorted out. If I had used the old wax motor, it would have caused the new parts I installed on the board to fail. I did find the wax motor cheaper on other companies web sites but without the instructions Richard provided, I would have had to spend nearly $300 on a new control board instead of repairing the original board. The two limit switches on the machine can be checked using an ohm-meter, so they only need to be replaced if they do not close when engaged which can be done manually. I found the resistor and Triac at Radio Shack online. I repaired the machine for about $40 total. Michael from Austin, TX

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.

remove door phillips remove front push down and pry out remove soap tray phillips remove two nut screws to lift up topy open tie or support top up remove bad contactor phillips normaly open check with continunity tester replace and reverse procedure

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!

When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.

Unplugged, removed back, removed hose, removed pump. Reversed the order and plugged it back in. Walla! Do'n wash again. Parts Select is the way to go.