MAH14PDBGW Maytag Washer - Instructions

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

My Maytag Neptune quit spinning. I found an on-line diagnostic tree and traced the problem to the wax motor. Testing indicated that the motor had failed even though it was still getting power. The continuity between the wax motor and control board appeared to test good. Based on the apparent diagnostic results, I found PartSelect, read their reviews, and ordered and installed the new wax motor. Once installed, I discovered the new wax motor would not work. I did some more online research .It helped me to find that I had a burned R11 on the control board. It's great for those who want to try their repair skills before ordering a new control board at nearly $350. I I contacted Neptunehelp.com and explained I had just purchased a new wax motor from PartSelect. Neptunehelp sent me the rest of their Stage 1 Repair kit at a discount by eliminating the wax motor in the kit. The kit included solder, a solder wick, a wire to open the printed circuit board holes, and both a new R11 and Q6. The site had a thorough explanation as to why both electronic components should be replaced at the same time...any why both should be replaced if the wax motor has failed. They also had an excellent video on some tricks about installing the wax motor, and an excellent video review on soldering tips if you want to attempt a repair on your own. PartSelect was OK for as far as it went, and the wax motor I purchased now works as it's supposed to. But I hope they will link to the Neptunehelp.com site to assist those who are more adventurous and have more advanced do-it-yourself skills. If you know anything about a VOM and have ever done a little soldering, it may be a better option than buying a wax motor and control board when only the was motor, R11, and Q6 are needed. I've completed the whole repair, including soldering in the new electronic components, and have just completed one wash cycle...the unit now works like new. If you are unsure about your electrical skills, you might want to stick with PartSelect and buy a wax motor and control board. If you're more experienced, and don't mind spending about $50 before having to spend nearly $400, then check out the Neptunehelp.com site for some good one-stop shopping and some good instructional references. They have a couple of contingency plans if the Stage 1 kit fails to fix the problem.

Followed the video, besides the spring, everything was easy.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.

remove door phillips remove front push down and pry out remove soap tray phillips remove two nut screws to lift up topy open tie or support top up remove bad contactor phillips normaly open check with continunity tester replace and reverse procedure

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

The video was great. The only problem was getting the spring back on. It was way too stiff, so I put it in a vise and stretched it a bit. It's a bit fussy but your site made it go pretty easy. thanks

The instructions from Richard of Austin, MN were instrumental in repairing my clothes washer. I am an electronics technician, and my control board failed just like Richard indicated. One thing Richard did not state is that resistor R11 and Q6 did not fail until the wax motor (solenoid) shorted out. If I had used the old wax motor, it would have caused the new parts I installed on the board to fail. I did find the wax motor cheaper on other companies web sites but without the instructions Richard provided, I would have had to spend nearly $300 on a new control board instead of repairing the original board. The two limit switches on the machine can be checked using an ohm-meter, so they only need to be replaced if they do not close when engaged which can be done manually. I found the resistor and Triac at Radio Shack online. I repaired the machine for about $40 total. Michael from Austin, TX

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.

First I took off the door and the front of the washing machine. Then, took off the bracket of the soap dispensing bin from the top of the machine. Then lift up the top of the machine, and unscrew the bracket that holds the wax motots, label and pull wires, replace motors and wires and put back together. This is also a good time to clean and dust the interior of the machine. Before replacing, my motor smelled and looked burnt out, instead of paying $300 -$400 to have someone look at it, I investigated and I fixed it for around $30. I hope I get to inspire people to figure things out and save some cash!!

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.