All Installation Instructions for Maytag Washer MAH14PDBEW

Rubber Boot between Tub and Door had a hole

When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!

Parts Used:

Bellow

David from El Paso, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set

Was this instruction helpful to you?

Door hinge hole covers broken

Unscrewed old screws, removed old plastic pieces, and replaced

Parts Used:

Hinge Screw

Hinge Hole Cover

Bruce from Sudbury, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set

Was this instruction helpful to you?

We had a leak in the tub pump hose

It was very easy...we ordered the part and it only took a day and a half and it was here.

Parts Used:

Tub to Pump Hose

Sandra from Slinger, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

Was this instruction helpful to you?

Would not enter spin cycle. Found WAX Motor not cycling, 120VAC present when disconnected. Applied 120VAC dierectly cycled OK.

When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.

Parts Used:

Door Lock/Spin Enable Switch

E T from Milton, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Water leak through door

I read the reviews from others fixing this same part, it didn't seem to difficult. It was not even hard at all. I installed the part and my washer does not leak at all. My Neptunes are old so I am very sure I will come back to buy parts here. I did install the hinges backwards at first, the didnt close so I had to take an extra five minutes to turn them around.

Parts Used:

Inner Door Liner with Vent

Rob from Orem, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

door boot seal broke

I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao

Parts Used:

Bellow

Davis from Sacramento, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

wouldn't spin out all of the water.

Replaced parts then the door wouldn't unlock, so we called a repair man and he's replacing the control board and the wireing harness, it cost 394.85 but the machine is in good shape so it was cheaper than buying a new washer and dryer, because I want them to match & the dryers only 7 years old.

Parts Used:

Door Lock/Spin Enable Switch

Wax Motor

MARILYN from SULLIVAN, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Started smelling rubber burning during spin cycle

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!

Parts Used:

Drive Belt and Motor Isolator Kit

Lauraine from Kimberling City, MO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

water leaking in the front of the machine

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

Parts Used:

Bellow

Susan from Mayville, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Water leaking from the rubber front door seal.

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

Parts Used:

Bellow

William from Sewickley, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

Was this instruction helpful to you?

leak in tub to pump hose

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

Parts Used:

Tub to Pump Hose

Philip from Parma, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Damaged bellow.

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

Parts Used:

Bellow

Jack from Great Falls, MT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Door sagging

The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.

Parts Used:

Door Hinge

Norma from Donald, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

The washer wouldn't spin the water out of the clothes

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

Parts Used: