MAH14PDBAW Maytag Washer - Instructions

Unscrewed old screws, removed old plastic pieces, and replaced

It was very easy...we ordered the part and it only took a day and a half and it was here.

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.

Syphon Cup is made one way and just slides into place...very easy

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

First I took off the door and the front of the washing machine. Then, took off the bracket of the soap dispensing bin from the top of the machine. Then lift up the top of the machine, and unscrew the bracket that holds the wax motots, label and pull wires, replace motors and wires and put back together. This is also a good time to clean and dust the interior of the machine. Before replacing, my motor smelled and looked burnt out, instead of paying $300 -$400 to have someone look at it, I investigated and I fixed it for around $30. I hope I get to inspire people to figure things out and save some cash!!

Removed 4 screws and door, lowered and removed front panel,removed screws holding locking tabs for the machine top, removed the four screws holding soap reservoir, lifted the top. Located under the lid and above the doorway I pulled out the wax motor retaineing clip with pliers and the wax motor, used pliers to remove the wire connectors, hooked them up to the new part and reassembled.

When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.

The instructions from Richard of Austin, MN were instrumental in repairing my clothes washer. I am an electronics technician, and my control board failed just like Richard indicated. One thing Richard did not state is that resistor R11 and Q6 did not fail until the wax motor (solenoid) shorted out. If I had used the old wax motor, it would have caused the new parts I installed on the board to fail. I did find the wax motor cheaper on other companies web sites but without the instructions Richard provided, I would have had to spend nearly $300 on a new control board instead of repairing the original board. The two limit switches on the machine can be checked using an ohm-meter, so they only need to be replaced if they do not close when engaged which can be done manually. I found the resistor and Triac at Radio Shack online. I repaired the machine for about $40 total. Michael from Austin, TX

I read the reviews from others fixing this same part, it didn't seem to difficult. It was not even hard at all. I installed the part and my washer does not leak at all. My Neptunes are old so I am very sure I will come back to buy parts here. I did install the hinges backwards at first, the didnt close so I had to take an extra five minutes to turn them around.

Replaced parts then the door wouldn't unlock, so we called a repair man and he's replacing the control board and the wireing harness, it cost 394.85 but the machine is in good shape so it was cheaper than buying a new washer and dryer, because I want them to match & the dryers only 7 years old.

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!