MAH14PDAGW Maytag Washer - Instructions

Received motor control board and new motor in one day - awesome! Took off front panel, disconnected power and water supplies. Disconnected wiring connections between motor control board and motor. Removed old control board. Removed back access panel. Replaced old motor with new motor. Put rear access panel back on. Installed new motor control board. Reconnected wiring connections between motor and control board. Put front panel back on. Reconnected power and water supplies. Done! The hardest part was moving my stack washer/dryer around to get at the rear access panel. I ended up putting the entire unit "face down" to make it easy to get access to the motor. Instructions that came with the motor/board kit were easy to follow. Only down side - I believe my old motor still worked fine. I'm sorry I had to replace it to replace the motor control board. Machine works great now.

Followed instructions that came with replacement part, good as new!

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

Well, if a picture is worth a thousand words, the repair video is priceless! Without it, this repair would have been more difficult, but it was so easy to follow along with the video while doing the repair. I rated it easy, but the reinstallation of the wire and spring holding the bellow in place requires significant pulling power. It took a couple tries to get it on, but other than that, the rest of it is cake. From start to finish, the job took less than an hour, but set aside some time for cleaning behind the washing machine if you haven't pulled it out in a while! Also, I have to mention that the part I received was an identical genuine Maytag part and not a remanufactured knock off. The fit and finish was perfect.

Watched the video, worked just like shown so as quick as you can take out 8 screws you can make the repair. Turned out it was the MCB but maybe this part (wax motor) Will save a main control board failure.

I went on your web site and printed the instructions given by the first entry after the product description. I had called my friend who is also a handy man and he did the repair very quickly [I helped very little]. The directions were very complete and very simple to follow. MAH5522BW

Watched the video. Video was great. Used a vicegrip to stretch spring since it was slipping out of normal pliers.

Replaced the belt and motor isolators. Watching your video made it very easy.

remove door with Phillips remove front panel nut driver remove soap tray lid and lift up top Phillips test small contactors for continuity and replace removed locking sprocket and replaced

Video repair instructions on the Parts Select site was right on and made the repair very easy. I took a little longer in my repair as I cleaned each piece I took off to make sure there was no dirt/lint/rust/mold remaining. The only difficult part was putting the spring back in place, this took a couple of tries. Other than that, relatively easy to replace and would recommend that anyone with any handyman skill to do this repair/replacement themselves.

The front seal had a long slit which leaks water during washing cycle. We followed the repair video every steps and got the old seal off really easy, the most difficult step is to tie the cable with the spring, it is too strong and can not be done with one person. All steps are the same as shown in the video. Thank you for providing the video and the part.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

Found the part on parts select, which also had a very helpful DIY repair video to replace the part. I followed the video step by step to fix the tub cover, and the washer is back to full working condition!!! I could not be happier with Partselect.com. Their easy appliance break down to find the exact part that is broken; but to also include a instructional video for that part was amazing.

removed front panel. removed brakets holding top. lifted top hinged backward. Removed tension spring and cable that secures the seal to the drum. Pulled seal out. Put new seal back in. Secured with cable and spring. Reassembled top and front.