MAH14PDABW Maytag Washer - Instructions

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

Replaced wax motor. You must also replace R11 (3.9 Ohm carbon film resistor (1/4 watt), Q6 Triac (Mouser 526-NTE5656), replaced Jp 18 (jumper) with a fuse (Mouser 576-0251.500HAT1l. This job requires the use of a solder sucker in order to remove parts without lifting up cooper traces.I have had experience with many electronic projects,and could have done this one easier if I still had the proper tools.A solder sucker is cheap, and without it, you will damage the traces. I did, but used a continuity checker to verify I made solder contact with the traces. I have six of these stacked washer/dryers. All failed after about a year of use. I am in absolute disbelief regarding all the stories about how easy this repair is.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

Well, if a picture is worth a thousand words, the repair video is priceless! Without it, this repair would have been more difficult, but it was so easy to follow along with the video while doing the repair. I rated it easy, but the reinstallation of the wire and spring holding the bellow in place requires significant pulling power. It took a couple tries to get it on, but other than that, the rest of it is cake. From start to finish, the job took less than an hour, but set aside some time for cleaning behind the washing machine if you haven't pulled it out in a while! Also, I have to mention that the part I received was an identical genuine Maytag part and not a remanufactured knock off. The fit and finish was perfect.

We read the instructions on the website which were very useful. We have a Maytag front loader. The instructions and pictures which came with the part are written to look like the hardware in the door and the door latch spring etc. is attached to the outer door. I realize this part fits multiple brands but instructions could clearly state that you have to remove all of the hardware from the inner door liner that you are replacing and reassemble it to the new inner door liner. It is really important to take pictures of how the door latch and spring are attached as this took the most time putting back on the new door liner. Our washer is older and did not have a vent tube and now has one. In the end, everything was correctly reassembled and we no longer have a leaky door. Shipping was very prompt and we're pleased with the part and repair.

Removed front panel and door, lifted top cover to access door lock. To remove the wax motor, you need to remove the Door Lock/Spin enable switch. Important note, there are two switches so to completely rebuild the door lock, you need get two of the Door Lock/Spin Enable switches. Same part/part number, one is for the door lock and the other for the Spin enable.

Received motor control board and new motor in one day - awesome! Took off front panel, disconnected power and water supplies. Disconnected wiring connections between motor control board and motor. Removed old control board. Removed back access panel. Replaced old motor with new motor. Put rear access panel back on. Installed new motor control board. Reconnected wiring connections between motor and control board. Put front panel back on. Reconnected power and water supplies. Done! The hardest part was moving my stack washer/dryer around to get at the rear access panel. I ended up putting the entire unit "face down" to make it easy to get access to the motor. Instructions that came with the motor/board kit were easy to follow. Only down side - I believe my old motor still worked fine. I'm sorry I had to replace it to replace the motor control board. Machine works great now.

Followed instructions that came with replacement part, good as new!

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

Unplug washer.Take off front panel by removing several screws. Lift up top after removing left and right side hold down bracket. Remove wax motor(brown item on left) The rotating latch will be free to remove and replace with new items. Don't forget to reattach spring. I found that my latch was not fully engaging with the teeth slightly misaligned. The locked light was on however there are two switches. One to control the lock light and one which enables the final spin to occur. After the items were changed unit ops normally. Also fast delivery (2 day) regular shipping!

removed front panel. removed brakets holding top. lifted top hinged backward. Removed tension spring and cable that secures the seal to the drum. Pulled seal out. Put new seal back in. Secured with cable and spring. Reassembled top and front.

easywaterways to diagnos and order the part. Very satisfied.

After removing the door, I pryd the bellows from the front of the washer then removed the front panel. I then rolled the spring from the rear of the Bellow and removed the old Bellow. Once I saw that the front edge of the washer drum was held on with spring clips I decided to remove it and clean the inside of that while I was in there. To get that part out I had to remove a couple cross braces. After cleaning I put it all back together. Getting the spring back on the back of the Bellow was a little challenging. Then put it all back together again. Now it looks great again.

Found the part on parts select, which also had a very helpful DIY repair video to replace the part. I followed the video step by step to fix the tub cover, and the washer is back to full working condition!!! I could not be happier with Partselect.com. Their easy appliance break down to find the exact part that is broken; but to also include a instructional video for that part was amazing.