LWC202 Maytag Dishwasher - Instructions

I removed front bottom cover,found belt broken. I ordered part online on 10-23-09,part arrived on 10-24-09,amazing. I lossened the two bolts that hold the drive motor to the frame,slipped the new belt on and applied the supplied silicone grease. I then ran the two bolts in with a 3/8 wrench,put the cover back on. Everything works like new now. Great delivery and easy ordering system online. Immediatly called my neighbor and told him about partselect.com

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

No problem at all. Belt slipped on very easily. Followed directions in the package.

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.

The water inlet valve would not allow enough water to run effectively. To R & R the part only a phillips screwdriver, a smaller adjustable wrench and pliers are needed. Turn the water supply off, & disconnect the water supply. Remove 2 screws attached to the cabinet and remove the rubber fill hose with pliers to open the clamp. Remove the inlet fitting from the old part and place on the new valve, using teflon tape. Attach the new part to the cabinet wall then the water supply to the old, reused fitting (also with teflon). Obviously, turn power off and disconnect the 2 double leads before beginning and replace when done. A fairly simple job , and my miraculous Maytag keeps on going!!

found the parts ordered them an poof dishwasher us as good as new

I opened the bottom part of the dishwasher, from there you can see all parts of the motor including the pulleys where the broken belt came from. From here, I took the new belt, placed some silicon all around it and installed it by rotating the pulleys clockwise until the belt wraps around it.
Then I tested it by turning the control on the Wash/Rinse mode and it started to drain the water right away.
DONE!

NO PROBLEM!!!

PS.
THANK YOU FOR DELIVERING IT ON TIME.

removed screws that secured cover plates. discovered that belt was broken. ordered new belt. ordered friday; delivered monday. read some previous repair experiences.

the trick to getting belt onto the pulleys is to first wrap it around the spindle part. then set the belt into the motor pulley groove. carefully start working the belt in the other pulley into the groove while rotating both pulleys. i had to lay on my stomach on the floor to do this, but it did not take very long. once the belt is in place, lubricate it with the included gel. took about 20 minutes with some trial and error.

This was a pain to change due to very limited access. Also belt had very little stretch. Had to really put some thought in it before attempting.

replaced belt....great service!!

lostened motor mounts,
streched belt across pulleys,
thghtened motor tension
replaced access panel.

After removing the cover to the motor assembly, I determined that the problem was that the old drive belt had broken. It probably was more than 20 years old. I originally thought that the size was no longer available because the old belt had stretched about two inches, but, after reading the repair stories on the PartsSelect Website, I decided to try the 25 3/8" belt. It worked great! After a few tries I was able to stretch the belt across the two pulleys without having to loosen anything. After applying the silicon grease, the dishwasher worked as good as new. The most difficult aspect of the job was having to work in such a small space. The most time-consuming part of the job was removing and then replacing the access cover, but the job overall was quite easy.

Read thru the comments by others and matched them up with what I found (belt off the pulleys) when I took off the kickplate below the door. The old belt (20 years) had stretched about 1 1/2" compaired to the new replacement. Slip the new belt on the motor pulley and start it around the back of the pump pulley. Get your wife to hold your legs down so you can really twist/pull the pump pulley until the belt finally slips into place. No need to loosen the motor mounts if your wife can hold you down.

First removed the four screws to the lower front outside panel (the only tools needed to complete this job). Slide the belt under the drive motor, onto the motor pulley grove, then strecthed the belt onto the pulley for the pump that's on the power module (was qiite difficult, but with the directions supplied with the belt, was able to get it on) Lubricated the belt with silicon grease.